

Country Crush Raptor Grip Rolling Handle
Key item features
- Country Crush Raptor Grip Rolling Handle
-
The Country Crush Raptor is a one-hand rolling handle built for arm wrestlers and grip athletes who want to train the exact angle they pull at. One free-spinning grip on a steel frame with three mounting points: clip in at the center for a straight pull, or off-center to load the pinky side or the thumb side and bias the fingers that do the work at the table. Clip it to a loading pin or a cable stack and lift. Made in the USA by Country Crush.
What It TrainsOn a fixed handle your fingers hook under the bar and your wrist helps. On the Raptor the grip spins freely, so the only thing holding the weight is finger and thumb pressure against the grip. That isolates crushing grip, thumb strength and wrist stability, and it is why rolling handles are the standard training tool in arm wrestling and grip sport.
The three mounting points are what set the Raptor apart from other one-hand rolling handles. Mount at the center and the load sits evenly across the hand. Mount at either end and the handle tilts under load, so you have to fight the roll with your pinky and ring finger on one side or your index finger and thumb on the other. That is the closest thing to table pressure you can get from a loading pin.
Which Size to Start WithThe grip diameter sets the difficulty. A smaller grip lets your fingers wrap and hold more weight; a larger grip forces an open hand and makes the same weight far harder to hold.
- 1.5" and 1.75": smaller hands, younger athletes, and anyone new to rolling handles.
- 2": the standard size and the one most arm wrestlers train on. If you are not sure, start here.
- 2.5" and 3": open-hand training for experienced lifters and for building the wide grip used against bigger opponents.
Grips swap in seconds and every size fits the same frame. Add sizes later from the Country Crush grips page; the Raptor takes a single grip, so buy singles. If you already own grips, choose Frame Only.
How to Use- Clip a carabiner through the mounting point you want: center for an even pull, either end to bias one side of the hand.
- Clip the carabiner to a loading pin and load plates, or to a cable stack.
- Grab the grip with a neutral wrist and lift. Keep the handle from rolling by squeezing the grip. If you let the weight settle into curled fingers the way you would on a fixed bar, the grip will spin out of your hand.
- Work in sets of 3 to 6 reps for strength, or hold at the top for 10 to 20 seconds for static endurance. Train both hands.
- Add weight when every rep finishes under control. Move up a grip size when the current one no longer rolls out of your hand at a hard weight.
For programming, follow the 12-Week Arm Wrestling Grip Program or the Country Crush 8-Week Rolling Handle Program.
Raptor or Country Crush Handle?The Raptor trains one hand at a time with a single grip and three mounting angles. The Country Crush Two-Hand Revolving Handle has two grips for training both hands together, which suits heavy rows, curls and high-volume forearm work. Most serious arm wrestlers end up with both; if you are buying one, the Raptor is the better match for table-specific one-hand training. The same grips fit both frames.
What's Included- One Country Crush Raptor frame with axle and pins
- One grip in the size you select (Frame Only ships without a grip)
Frame height (base to carabiner loop) 7 3/4 inches Frame weight (without grip) 3.0 lb Grip weight 1.5": 0.26 lb · 1.75": 0.38 lb · 2": 0.51 lb · 2.5": 0.83 lb · 3": 1.22 lb Grip sizes available 1.5", 1.75", 2", 2.5", 3" (one grip per handle) Mounting points Three: center, and one at each end for an off-center pull Attachment Carabiner to a loading pin - By Country Crush
Specs
Brand, Country Crush
Items included, Revolving Handle
Activity, Weight Lifting
Sport, Weightlifting, Arm wrestling, Rock climbing, Boxing
Retail packaging, Single Piece
About this item
Product details
The Country Crush Raptor is a one-hand rolling handle built for arm wrestlers and grip athletes who want to train the exact angle they pull at. One free-spinning grip on a steel frame with three mounting points: clip in at the center for a straight pull, or off-center to load the pinky side or the thumb side and bias the fingers that do the work at the table. Clip it to a loading pin or a cable stack and lift. Made in the USA by Country Crush.
What It TrainsOn a fixed handle your fingers hook under the bar and your wrist helps. On the Raptor the grip spins freely, so the only thing holding the weight is finger and thumb pressure against the grip. That isolates crushing grip, thumb strength and wrist stability, and it is why rolling handles are the standard training tool in arm wrestling and grip sport.
The three mounting points are what set the Raptor apart from other one-hand rolling handles. Mount at the center and the load sits evenly across the hand. Mount at either end and the handle tilts under load, so you have to fight the roll with your pinky and ring finger on one side or your index finger and thumb on the other. That is the closest thing to table pressure you can get from a loading pin.
Which Size to Start WithThe grip diameter sets the difficulty. A smaller grip lets your fingers wrap and hold more weight; a larger grip forces an open hand and makes the same weight far harder to hold.
- 1.5" and 1.75": smaller hands, younger athletes, and anyone new to rolling handles.
- 2": the standard size and the one most arm wrestlers train on. If you are not sure, start here.
- 2.5" and 3": open-hand training for experienced lifters and for building the wide grip used against bigger opponents.
Grips swap in seconds and every size fits the same frame. Add sizes later from the Country Crush grips page; the Raptor takes a single grip, so buy singles. If you already own grips, choose Frame Only.
How to Use- Clip a carabiner through the mounting point you want: center for an even pull, either end to bias one side of the hand.
- Clip the carabiner to a loading pin and load plates, or to a cable stack.
- Grab the grip with a neutral wrist and lift. Keep the handle from rolling by squeezing the grip. If you let the weight settle into curled fingers the way you would on a fixed bar, the grip will spin out of your hand.
- Work in sets of 3 to 6 reps for strength, or hold at the top for 10 to 20 seconds for static endurance. Train both hands.
- Add weight when every rep finishes under control. Move up a grip size when the current one no longer rolls out of your hand at a hard weight.
For programming, follow the 12-Week Arm Wrestling Grip Program or the Country Crush 8-Week Rolling Handle Program.
Raptor or Country Crush Handle?The Raptor trains one hand at a time with a single grip and three mounting angles. The Country Crush Two-Hand Revolving Handle has two grips for training both hands together, which suits heavy rows, curls and high-volume forearm work. Most serious arm wrestlers end up with both; if you are buying one, the Raptor is the better match for table-specific one-hand training. The same grips fit both frames.
What's Included- One Country Crush Raptor frame with axle and pins
- One grip in the size you select (Frame Only ships without a grip)
| Frame height (base to carabiner loop) | 7 3/4 inches |
| Frame weight (without grip) | 3.0 lb |
| Grip weight | 1.5": 0.26 lb · 1.75": 0.38 lb · 2": 0.51 lb · 2.5": 0.83 lb · 3": 1.22 lb |
| Grip sizes available | 1.5", 1.75", 2", 2.5", 3" (one grip per handle) |
| Mounting points | Three: center, and one at each end for an off-center pull |
| Attachment | Carabiner to a loading pin |
- Country Crush Raptor Grip Rolling Handle
-
The Country Crush Raptor is a one-hand rolling handle built for arm wrestlers and grip athletes who want to train the exact angle they pull at. One free-spinning grip on a steel frame with three mounting points: clip in at the center for a straight pull, or off-center to load the pinky side or the thumb side and bias the fingers that do the work at the table. Clip it to a loading pin or a cable stack and lift. Made in the USA by Country Crush.
What It TrainsOn a fixed handle your fingers hook under the bar and your wrist helps. On the Raptor the grip spins freely, so the only thing holding the weight is finger and thumb pressure against the grip. That isolates crushing grip, thumb strength and wrist stability, and it is why rolling handles are the standard training tool in arm wrestling and grip sport.
The three mounting points are what set the Raptor apart from other one-hand rolling handles. Mount at the center and the load sits evenly across the hand. Mount at either end and the handle tilts under load, so you have to fight the roll with your pinky and ring finger on one side or your index finger and thumb on the other. That is the closest thing to table pressure you can get from a loading pin.
Which Size to Start WithThe grip diameter sets the difficulty. A smaller grip lets your fingers wrap and hold more weight; a larger grip forces an open hand and makes the same weight far harder to hold.
- 1.5" and 1.75": smaller hands, younger athletes, and anyone new to rolling handles.
- 2": the standard size and the one most arm wrestlers train on. If you are not sure, start here.
- 2.5" and 3": open-hand training for experienced lifters and for building the wide grip used against bigger opponents.
Grips swap in seconds and every size fits the same frame. Add sizes later from the Country Crush grips page; the Raptor takes a single grip, so buy singles. If you already own grips, choose Frame Only.
How to Use- Clip a carabiner through the mounting point you want: center for an even pull, either end to bias one side of the hand.
- Clip the carabiner to a loading pin and load plates, or to a cable stack.
- Grab the grip with a neutral wrist and lift. Keep the handle from rolling by squeezing the grip. If you let the weight settle into curled fingers the way you would on a fixed bar, the grip will spin out of your hand.
- Work in sets of 3 to 6 reps for strength, or hold at the top for 10 to 20 seconds for static endurance. Train both hands.
- Add weight when every rep finishes under control. Move up a grip size when the current one no longer rolls out of your hand at a hard weight.
For programming, follow the 12-Week Arm Wrestling Grip Program or the Country Crush 8-Week Rolling Handle Program.
Raptor or Country Crush Handle?The Raptor trains one hand at a time with a single grip and three mounting angles. The Country Crush Two-Hand Revolving Handle has two grips for training both hands together, which suits heavy rows, curls and high-volume forearm work. Most serious arm wrestlers end up with both; if you are buying one, the Raptor is the better match for table-specific one-hand training. The same grips fit both frames.
What's Included- One Country Crush Raptor frame with axle and pins
- One grip in the size you select (Frame Only ships without a grip)
Frame height (base to carabiner loop) 7 3/4 inches Frame weight (without grip) 3.0 lb Grip weight 1.5": 0.26 lb · 1.75": 0.38 lb · 2": 0.51 lb · 2.5": 0.83 lb · 3": 1.22 lb Grip sizes available 1.5", 1.75", 2", 2.5", 3" (one grip per handle) Mounting points Three: center, and one at each end for an off-center pull Attachment Carabiner to a loading pin - By Country Crush
Specifications
Fitness goal
Brand
Items included
Activity
Warranty
Warranty information
Customer ratings & reviews
Filtered and sorted results would be available on the new 'Customer ratings & reviews' page.
Showing 1-1 of 1 review
Forearm blaster
The raptor handle is another beast handle cant compare it to the original country crush handle because it gives you so many different angle to hit and with interchangeable grips its more than enough to burn out those forearms!
- Free shipping
Free Holiday returns until Jan 31
