Hero image 0 of Silicone Christmas Ornament Mould, 2 Piece Round Pendant Set With A Hanging Hole, Reusable Casting Tray For Craft, 0 of 3
New
Silicone Christmas Ornament Mould, 2 Piece Round Pendant Set With A Hanging Hole, Reusable Casting Tray For Craft
(No ratings yet)
Key item features
- The piece is a silicone ornament mould cast as a round disc, with a raised rim and a well deep enough for resin or plaster. Read as a round pendant mould it makes a disc that hangs rather than stands, and the hanging hole is part of the cavity rather than a drill. The silicone is soft enough to flex, so a cast lifts out with a thumb instead of a knife. A flat base keeps the mould level while it fills. The wall is thick at the rim so it does not flop. A slight taper lets a cured disc start at one edge.
- Sold as a 2 piece mould set, the pair covers two motifs on the same disc, so one pour gives a choice of face. As a hanging hole mould the top of the cavity is shaped rather than drilled, which leaves a clean loop. A short pour lip guides resin back into the well instead of down the side. The two moulds stack for storage without touching a face. Each one is marked on the base with its design. A small tab starts the lift. A shallow well keeps a pour from running over the lip, and a flat back sits steady.
- The body is a resin casting mould in flexible silicone, so a set piece pops out without a release agent once it has cured. The surface is polished inside the cavity, which is why a cast comes out clear rather than cloudy. A thin wall at the edge lets a fingernail start the rim. The mould takes a warm pour without deforming. Nothing is scented, so a craft table stays neutral. The rim holds a level pour. A warm room cures a thin disc faster than a cold one, so a first cast is not a long wait.
- Read as a diy ornament project the mould suits a first cast, because the cavity is open rather than split. A craft table mould of this size fits on a mat with room for a mixing cup. A short cure in a warm room is enough before the cast lifts. Where a cast sticks, a drop of soap in water releases it. The disc takes a hook through the hole without a drill. A paper towel under the tray catches a drip. A shot glass measures the two parts, which keeps a mix inside its working time without a scale.
- The disc measures about 7cm (2.8 inch) across, so the round mould pair suits a tree ornament rather than a wall plaque. It is a reusable mould in the plain sense: wash it, dry it and pour again. A damp cloth lifts resin from the cavity, and the mould should be dried flat rather than hung. Keep it out of direct sun so the silicone does not yellow. A short soak lifts a cured skin without a pick. A clean pour leaves no skin to trim, so the edge of a cast stays sharp and the hole stays round.
Specs
Color, Black
Material, Silica gel
Size, One Size
Brand, Loniway
Pieces, 1
Weight, 0.09 lb
Color
Black
Material, Silica gel
Material
Silica gel
Size, One Size
Size
One Size
Brand, Loniway
Brand
Loniway
Pieces, 1
Pieces
1
Weight, 0.09 lb
Weight
0.09 lb
About this item
Product details
A round disc mould cast in a soft silicone, with a raised rim and a well deep enough for resin or plaster, and the hanging hole formed as part of the cavity rather than drilled after. Two moulds ship together, each carrying a different face on the same disc, so one pour gives a choice. The inside is polished, which is why a cast lifts clear instead of cloudy, and a thin wall at the edge lets a fingernail start the release. At about 7cm across the disc suits a tree ornament. Sold as a pendant mould kit it washes and pours again, so ornament casting repeats without a new tray.
- The piece is a silicone ornament mould cast as a round disc, with a raised rim and a well deep enough for resin or plaster. Read as a round pendant mould it makes a disc that hangs rather than stands, and the hanging hole is part of the cavity rather than a drill. The silicone is soft enough to flex, so a cast lifts out with a thumb instead of a knife. A flat base keeps the mould level while it fills. The wall is thick at the rim so it does not flop. A slight taper lets a cured disc start at one edge.
- Sold as a 2 piece mould set, the pair covers two motifs on the same disc, so one pour gives a choice of face. As a hanging hole mould the top of the cavity is shaped rather than drilled, which leaves a clean loop. A short pour lip guides resin back into the well instead of down the side. The two moulds stack for storage without touching a face. Each one is marked on the base with its design. A small tab starts the lift. A shallow well keeps a pour from running over the lip, and a flat back sits steady.
- The body is a resin casting mould in flexible silicone, so a set piece pops out without a release agent once it has cured. The surface is polished inside the cavity, which is why a cast comes out clear rather than cloudy. A thin wall at the edge lets a fingernail start the rim. The mould takes a warm pour without deforming. Nothing is scented, so a craft table stays neutral. The rim holds a level pour. A warm room cures a thin disc faster than a cold one, so a first cast is not a long wait.
- Read as a diy ornament project the mould suits a first cast, because the cavity is open rather than split. A craft table mould of this size fits on a mat with room for a mixing cup. A short cure in a warm room is enough before the cast lifts. Where a cast sticks, a drop of soap in water releases it. The disc takes a hook through the hole without a drill. A paper towel under the tray catches a drip. A shot glass measures the two parts, which keeps a mix inside its working time without a scale.
- The disc measures about 7cm (2.8 inch) across, so the round mould pair suits a tree ornament rather than a wall plaque. It is a reusable mould in the plain sense: wash it, dry it and pour again. A damp cloth lifts resin from the cavity, and the mould should be dried flat rather than hung. Keep it out of direct sun so the silicone does not yellow. A short soak lifts a cured skin without a pick. A clean pour leaves no skin to trim, so the edge of a cast stays sharp and the hole stays round.
info:
We aim to show you accurate product information. Manufacturers, suppliers and others provide what you see here, and we have not verified it.
Specifications
Color
Black
Material
Silica gel
Size
One Size
Brand
Loniway
Warranty
Warranty information
Please be aware that the warranty terms on items offered for sale by third party Marketplace sellers may differ from those displayed in this section (if any). To confirm warranty terms on an item offered for sale by a third party Marketplace seller, please use the 'Contact seller' feature on the third party Marketplace seller's information page and request the item's warranty terms prior to purchase.
Customer ratings & reviews
0 out of 5 stars
This item does not have any reviews yet
Current price is USD$5.69
Price when purchased online
- Free shipping
Free Holiday returns until Jan 31
How do you want your item?
Ships to
Arrives between Nov 21 - Nov 28
|
Sold and shipped by MKdclsx
3.2830188679245285 out of 5 stars
Extended holiday returns
Free Holiday returns until Jan 31