Instructions
. Pull dents, patch holes, and make small repairs. Directions for Use: (Read all directions and warnings for safe and warnings for safe and proper application.). 1. Clean the repair area using soap and water followed by a residue remover or surface cleaner to remove dirt, grease, oil, wax and moisture. Allow to dry. 2. Sand to the bare surface as needed with 3M 40 or 80 grit sandpaper. Note: if grinding is required, use 3M 36 or 40 grit grinding discs. Roughen area 1” beyond the repair. Remove dust with a tack cloth or blow off the sanding dust with clean dry air. Re-clean surface using a clean paper or cloth towel and a residue remover or surface cleaner. 3. Mixing: Knead cream hardener tube thoroughly. For a golf ball-size amount of filler, squeeze out 1 1/4 inch strip of hardener, or mix a 3 inch diameter circle 1/2 inch thick of filler to a 3 inch strip of cream hardener. Mix thoroughly to a uniform color on clean, non-porous surface. Mix only small amounts that can be used within 3-4 minutes. Do not add cream hardener in filler container. Spread initial thin layer of mixed filler over repair area using firm pressure to ensure maximum adhesion. 4. Let repair cure for at least 12-15 minutes. File excess material. Use sanding block with 3M 80 grit sandpaper to sand repair area to contours of original surface. Open any soft spots, dry fiber pits or pinholes with a sharp knife tip and clean area with cloth. 5. To fill in pinholes and to get a uniform, smooth surface for painting, topcoat the repair with Bondo® Body Filler. Follow directions for use on the can. 6. Mask the area not to be painted. Use primer to spray 2-3 coats evenly and cover the entire repair area. When dry, sand primer with 3M 320 grit sandpaper. Apply thin coat of Bondo® Glazing and Spot Putty to fill in small imperfections. Sand with 3M 320 grit sandpaper and re-prime with 2-3 coats. Wet or dry sand with 3M 400 grit 3M Wetordy™ sandpaper. Finish paint to desired color per paint manufacturer's recommendation and paint finish with 3M fine grit sandpapers, compounds and polishes. Do not put mixedmaterial back in the can. For best results apply at 45° F (7° C) or above. Clean tools with acetone.
Safe Handling Instructions
WARNING! OXIDIZER. FLAMMABLE LIQUID AND VAPOR. CAUSE EYE IRRITATION. MAY CAUSE ALLERGIC SKIN REACTION. Read carefully other cautions on the side/back panel. WARNING! HARDENER HAZARDS: OXIDIZER. CAUSES EYE IRRITATION. MAY CAUSE ALLERGIC SKIN REACTION. May cause skin, nose and throat irritation. WARNING! FILLER HAZARDS: FLAMMABLE LIQUID AND VAPOR. Vapor harmful. May irritate the eyes, skin, nose and throat and cause dizziness, headache or nausea. Contains a chemical(s) which can cause cancer. PRECAUTIONS: Vapor may cause flash fire. Keep away from heat, sparks, flame and sources of static discharge. Avoid eye contact. Do not get on skin or clothing. Avoid breathing dust or vapors. Use only with adequate ventilation. Do not swallow. Wash thoroughly after handling. Close container after each use. FIRST AID INFORMATION: EYE CONTACT: Immediately flush eyes with large amounts of water for at least 15 minutes. Get immediate medical attention. SKIN CONTACT: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical attention. Wash contaminated clothing and clean shoes before reuse. INHALATION: Remove person to fresh air. If signs/symptoms develop, get medical attention. IF SWALLOWED: Do not induce vomiting. Get medical attention. KEEP OUT OF REACH OF CHILDREN. For application or technical information, call 1-800-421-2663 or (404) 696-2730
