Ergodyne ProFlex 7501 Waterproof Winter Work Gloves Gray Small 12 Pairs (17632)

[This review was collected as part of a promotion.] The ProFlex 7501 Coated Waterproof Winter Work Gloves from Ergodyne have proven highly effective during 10 days of rigorous testing. I am in the Water Mitigation and Fire Restoration industry in St. Paul MN. So this provides me the perfect opportunity to put these gloves to work. I kept a daily journal from January 15 through January 24, 2026. To keep track of my real time thoughts on the gloves. Temperatures were in the single digits to mid-20s Fahrenheit, occasional light snow or sleet, and high humidity from wet job sites. The gloves were used exclusively for restoration tasks, including water extraction, structural drying, soot and debris removal, content manipulation, and equipment handling. Daily Journal Entries 1/15/26 DAY ONE I was very pleased upon opening the box to see a visually high quality product. They looked very clean, sleek, and like an actual pair of work gloves. They are for sure thicker than I had expected. Which is good. Putting them on felt good. I did not have to struggle getting them on. They are a good snug fit for my hands. No extra material hanging or maybe getting caught on something. This morning in St Paul MN it was 9 degrees outside. They were the only gloves I had and I was fine. I did also have my hands in my jacket pockets but it was all good. I work outside before the sun comes up so my hands being warm matters very much. I wore them till lunch time no issues all day. The one thing I wish they would do is be touch screen capable. I cannot use them on my iPhone XR screen. 1/16/26 DAY TWO I left the house at 5:32am to walk 0.8 miles to the bus stop. It is 23 degrees in St Paul this morning. My gloves have kept my digits perfectly warm the whole walk. Arrived at a water mitigation job site involving flooded basement extraction. Hands submerged while positioning pumps and hoses—no water penetration through the full latex coating. Fingers stayed warm despite direct cold water contact. Sandy nitrile palm provided secure grip on wet, slippery surfaces. No slippage when handling saturated hoses or extraction wands. Dexterity adequate for securing fittings and operating controls. 1/17/26 DAY THREE Continued water mitigation: removed wet drywall and insulation in an unheated structure at approximately 15°F ambient. Gloves resisted moisture from soaked materials and prevented cold air infiltration. They kept my hands comfortable during prolonged exposure. Excellent abrasion resistance noted when handling rough, jagged edges—no wear or discomfort. Grip remained reliable even on damp, debris-covered items. 1/18/26 DAY FOUR Transitioned to fire restoration site with soot-heavy cleanup. Gloves handled charred wood, ash, and broken glass remnants effectively. ANSI A2 cut resistance and level 4 abrasion protection performed well against incidental sharp contacts—no cuts or punctures. Latex coating minimized soot adhesion, making post-shift cleanup easier. Hands remained dry and warm in the cold, soot-laden environment. 1/19/26 DAY FIVE Full day of content packing and moving in a post-fire/water-damaged residence. Manipulated furniture, boxes, and personal items covered in residue. Superior wet/dry grip from sandy nitrile palm prevented drops despite heavy, awkward loads. Knit cuff reduced particulate entry. No internal clamminess despite moderate exertion and insulation. 1/20/26 DAY SIX Intensive drying setup: positioned air movers, dehumidifiers, and moisture barriers in sub-zero wind chill conditions (felt like 0°F). Gloves flexed well in the cold without stiffening, allowing precise tool adjustments. Waterproofing held during contact with condensation-heavy equipment. Touchscreen functionality tested again after light fingertip cleaning—responsive swiping and tapping on iPhone XR for logging readings and photos. 1/21/26 DAY SEVEN Demolition phase: pried apart damaged cabinetry and trim with tools. Level 2 puncture resistance protected against nails and splinters. No breaches observed. Thermal retention excellent during extended outdoor-to-indoor transitions in fluctuating temperatures (12–28°F). Dexterity supported fastening straps and operating power tools without removal. 1/22/26 DAY EIGHT Soot wiping and surface prep with mild cleaners. Coating resisted light chemical contact and residue buildup. Grip maintained on slick, treated surfaces. Hands comfortable throughout 8-hour shift—no hotspots or fatigue from the snug fit. 1/23/26 DAY NINE Mixed tasks: water extraction follow-up and debris hauling. Gloves endured repeated wet/dry cycles without degradation. Warmth consistent even during breaks in unheated areas. Machine-washable feature anticipated to simplify decontamination after soot exposure. 1/24/26 DAY TEN Final day: comprehensive site walkthrough and equipment breakdown. Gloves showed minimal visible wear after cumulative use. Overall comfort, protection, and performance remained high. Touchscreen interaction reliable for final documentation. Summary The Ergodyne ProFlex 7501 excels in water mitigation and fire restoration applications by integrating full waterproof latex coating, dual-layer thermal insulation, superior sandy nitrile grip, and moderate cut/abrasion protection (ANSI/ISEA 105-2016 A2 cut, level 4 abrasion; EN 388: 2131X). These attributes directly address key hazards: prolonged wet exposure, cold stress, slippery surfaces, and incidental sharp edges common in restoration work. Waterproofing prevented moisture ingress during submersion and saturated material handling, preserving internal dryness and warmth. Thermal performance was outstanding in sub-freezing conditions, eliminating cold-related discomfort. Grip reliability enhanced safety and efficiency when manipulating wet, sooty, or heavy items. Touchscreen capability—after minor adjustment—supported on-site documentation without compromising protection. Durability held strong with no significant coating wear, liner breakdown, or fit loss over the period. The gloves balance dexterity for practical tasks while prioritizing cold/wet protection, outperforming many alternatives lacking integrated waterproofing or thermal layering. Recommendation: These gloves are highly recommended for restoration professionals in cold, wet climates like the Upper Midwest. They provide reliable, multi-hazard protection suitable for structural drying, extraction, soot cleanup, and content handling. For general winter restoration work, the ProFlex 7501 delivers exceptional value and performance.

[This review was collected as part of a promotion.] The winter work gloves are a great product! I was extremely surprised how warm and how dry they kept my hands during my work task ( electrical work: terminating feeder wires) . The weather was cold and extremely foggy in the region so everything was cold and extremly moist due to the fog. With the winter work gloves the cold , wet/ moist objects and grip were not a problem. But due to the thickness of the glove and insulation , my only issue was with finger dexterity portions of my work task ( using hardware such as bolts , fender washers , lock washers , and nuts). Aside from this minor issue the it did not stop me from using the product as I felt that my hands being warm and dry along with the ability to grip the and manipulate the feeder wire outweighed the negative of finger dexterity. I will definitely continue to use the winter work gloved and I appreciate the Ergodyne team for giving me the opportunity to keep my hands dry and warm!