3MM Feed Pellet Mill Machine Poultry Chicken Fish Feed Granulator with 3 Head Press Roller 220V 3.5KW

Product Overview:
Feed granulator is widely used in large, medium and small aquaculture, grain feed processing plants, livestock farms, poultry farms, individual farmers and small and medium-sized farms, farmers or large, medium and small feed processing plants.
This machine can be used alone, and customers who need it can also match it with a straw cutter for better results.

Product Parameter:
Pressure plate: 3MM
Output/h: Maximum output 150KG (ideal state)
Power: 3.5KW
Voltage: 220V Single-phase electricity
Product body material: Cast iron
Standard pressure roller: Three head press roller
Product size: 27.56*11.22*34.6in (70*28.5*88cm)

Note:
1.Do not touch the running parts during operation.
Do not put the hands into the machine.
2.Before using the machine, it is necessary to adjust the screw of the pressure roller to the appropriate position. The pressure roller and the pressure plate should be closely combined, and the three adjusting screws should be on the same horizontal plane.
3.Please refuel the fuel tank before using the machine. The machine should not idle for more than 2 minutes.
4.Double-check the belt and the screws before operation.
5.Clean up the rest after use to prevent damage to the machine.
6.If the pressure roller cannot rotate normally, please tighten the screws that control the pressure roller first, and then try to power it on. If it still does not work, you can appropriately loosen the screws next to the pressure roller and then tighten them slightly again (without special tightening)
7.The colors of air switches and wires are randomly shipped.
8.The operation steps for disassembling and installing the grinding disc are consistent for double head pressure rollers, three head pressure rollers, and four head pressure rollers. The webpage only uses the double head pressure roller model as an example of operation.
9.We suggest that high-power machines should be directly connected to the main power supply, as the voltage reaching the machine is stable. If the voltage is unstable and the current exceeds the rated current of the motor, it is easy to burn out the starting capacitor.
9.It is recommended to directly connect to the power supply as much as possible. If the machine is not connected to the power supply, different situations may occur, and the wires are not durable. The wires will gradually burn out over time.
10.Our machine is not equipped with a plug. If you do not know how to operate the wiring video, you can contact our customer service and we will provide you with the wiring video. (If there are occasional situations with plugs, it is also recommended that you remove the plugs when wiring).
11.The output of the feed pellet machine just received is too low, and it is normal to produce a lot of powder or even no pellets because it is a brand new machine and needs a certain running-in time. When the die hole finish is poor for the first time, it is necessary to use abrasives to grind the template. After the machine has been used for a period of time and the various parts of the pellet machine run in the best state, the yield and output quality of the pellet machine will reach the best state. It is a normal phenomenon.

Precautions:
1.When using, it should be noted that there should be no foreign matter such as stones and iron blocks in the raw materials. After the pellet machine has been working continuously for more than ten shifts, the pressure roller oil hole, the universal joint oil hole, and the linkage shaft oil hole need to be filled with high-temperature lubricating grease to make the pressure roller have good working performance and extended bearing life.
2.During granulation, it is strictly forbidden for the pressure roller to make contact with the template to run idly, and the continuous feeding can not be interrupted.At the same time, the pressure roller shaft nut is locked to avoid loosening and damaging the spindle keyway.
3.When granulating, there is no granulation and no discharge, the template should be removed, and after opening one by one, some fiber feed can be added appropriately to restart the granulation.
4.Always check the tightness of the screws in each part of the machine. If there is oil leakage in the gearbox, replace the oil seals in time, and check whether the bearings in the machine head are short of oil.
5.When the pellet machine is working, do not reach into the feeding port with your hands. If necessary, use wooden sticks to help feed the pellets.
6.Before turning on the machine, it is necessary to add less materials. When shutting it down, leave a small amount of feed in the machine to prevent the press roller of the machine from contacting the template to idle.
7.If the machine is stuck in operation, stop it immediately, press the pressure roller until the bolt is flat,and then restart the machine.
8.Each time the work is completed, the adjusting pressure roller bolts must be loosened.
9.Iron or stones cannot be put into the machine.
10.Check the elasticity of the belt, and the bearing frequently. Add oil in time when it needed.

Usage and Specification:
1: It applies to chicken industry.
2:Corn particles can be put into the machine directly. The feed processed by the machine is smooth and has moderate hardness. The temperature change in the process is slight so the nutrition can be maintained very well.
3:The practical diameter of the holes can be divided into: Φ2, Φ3, Φ4, Φ5, Φ6, Φ8, Φ10, Φ12.
4:The microorganism and parasite can be killed by extrusion in the process.

Item Number:(238013)
1*Chicken Feed Pellet Mill Machine 220V