D05 (NG10): Hydraulic Electrical Solenoid Control Valve: 31 GPM: 4560 psi: 110VAC 220VAC 12VDC 24VDC: Wiring Box (Balers and Compactors)

For a larger view of images, right click on the image and select "Open in a new tab" 

Link to: Catalog

Hydraulic Directional Control Valve.  Proven high quality robust valve design successfully designed into many high volume applications.

Often used in Balers and compactors

Compare to:  Nachi SS-G03-__-FR-E115-E31

• Terminal box with 1/2" conduit connection.
• D05 (NG10) Cetop mounting.  Can be mounted to standard available subplates and bar manifolds.
• Maximum flow of 31 gpm
• Maximum working pressure = 4560psi (315 Bar)
• 3-position, 4-way, Spring centered, energize to shift
• Double solenoid operated
• Solenoid Power: DC= 35 watts, AC = 90VA (550VA inrush)
• Operating temperature =  -22Ö¯F to 174Ö¯F
• Removable Coil
• Valve can be mounted in any direction
• LED illuminate’s clear connector housing when power is supplied to the connector/coil.  
• NBR Buna seals
• Use with mineral based hydraulic fluid.
• Four fastening screws included, M6x40mm long
• White label with no logo for OEM manufacturers.

Options:

Solenoid Voltage: 12VDC, 24VDC, 110VAC (50 or 60 hz), 220VAC (50 or 60 hz)

Spool Configurations:

Spool Configurations:

C:  Closed center spool, all ports blocked when centered.

 

Used to switch actuator (motor or cylinder) directions by energizing solenoid “a” or “b”.  Actuator fully stops when solenoids are not energized and spool is spring centered.  Make sure there is a relief valve to protect overrunning loads from spiking the pressure during sudden stops when centering.  Note that there is a small amount of oil leakage across any spool type valve manufacturer. This means there could be slow drifting of the actuator in the center position.  Use a Pilot Operated Check Valve Fluidhaus series VMCP6 with the M Valve spool type if you need to hold position over a long period of time.

M:  Motor spool, A and B ports to tank and P port blocked when centered. 

 

Actuators will move freely from external forces when the valve is in the center position (solenoids de-energized).  Motors and cylinders will coast to a stop when centering.  Adding an A&B port P.O. check valve (Fluidhaus Series VMCP6-AB-1 ) under this valve will ensure a positive stop and hold the position of a motor and cylinder for longer durations than with just a closed center spool valve C.

T:  Tandem Spool, A and B ports closed and P to T in center position:

 

Actuators will stop in center position and the supply pressure will be directed to tank.  Commonly used with fixed displacement gear pumps so pressure can flow direct to tank and not build up heat by blowing across a relieve valve as would be needed with the M and C spool.  Also used in series circuits to supply pressure to the next valve through the T port.

H: Open Center Spool, A, B, P and T ports connected in center.

 

Actuators will freely move when valve is de-energized, and spring centered.  Pressure and all ports will drain to tank.  Energize solenoid “a” and “b” to change directions of actuator.

 

R: Regeneration Spool: All Ports are closed in the spring center position.  When the

    “b” solenoid is shifted the rod side of a cylinder will connect to the piston side

    along with supply pressure. 

 

 Mounting Pattern of mating surface (mm):

 

High volume OEM series production available per request.