Hero image 0 of Steinjäger Cable, Universal Cables, Push-Pull 10-32 60 inches long Bulkhead Style, 0 of 3

Steinjäger Cable, Universal Cables, Push-Pull 10-32 60 inches long Bulkhead Style

(No ratings yet)

Key item features

QUANTITY PER PACKAGE: ONE CABLE. PRODUCT NAME: SHIFTER CABLE CABLE LENGTH: 60" THREAD: 10-32 RH CABLE TRAVEL: 3" (COMMENT: THE USABLE STROKE 'TRAVEL' OF A CABLE SHOULD BE CENTERED ON THE TRAVEL RANGE). LINKAGE END: (2) PLATED 10-32 RH JAM NUTS SWIVEL ANGLE: THIS TERM REFERS TO THE SLIGHT MISALIGNMENT ALLOWABLE IN THE PUSH-PULL STROKE OF THE CABLE AS IS ACCOMPLISHED BY THE GUIDE 'TUBE' (THE PIECE BETWEEN THE END OF THE CONDUIT AND THE TRAVEL 'END ROD'). THE MAXIMUM CONICAL MOVEMENT AROUND THIS CENTERLINE SHOULD NOT EXCEED 16°. INSTALLATION: DO NOT BEND ANY OF THE VISIBLE METAL PIECES, OR ANY OF THE INTERSECTIONS OF THESE VISIBLE METAL PIECES; THESE COMPONENTS ARE DESIGNED FOR A PUSH-PULL LOAD ONLY. ONLY INSTALL CABLES WHEN ALL MOTORS, ENGINES, AND POWER SOURCES ARE TURNED OFF. BEND RADII WARNING: EACH CABLE HAS A SPECIFIED MINIMUM BEND RADIUS. FAILURE TO OBSERVE THIS MINIMUM CAN AT A MINIMUM INCREASE THE FORCE IT TAKES TO MOVE THE CABLE, AND AT WORSE, CAN CAUSE THE CABLE TO KINK INSIDE OF THE CONDUIT, WHICH IN TURN CAN CAUSE THE CABLE TO FAIL AND/OR NOT OPERATE PROPERLY. BEND RADIUS MINIMUM: 6" MAXIMUM INPUT LOAD: 75 LBS OPERATING TEMPERATURE RANGES: -65° F TO 225° F COMMON OTHER NAMES FOR THIS PRODUCT: CONTROL CABLE, THROTTLE CABLE, PUSH-PULL CABLE, HEAVY DUTY PUSH PULL CABLE. BACKLASH: THIS TERM IS USED TO DESCRIBE THE MOTION LOST IN MOVING (ACTUATING) THE CABLE. ALTHOUGH THE CABLE DESIGN EFFECTS THIS TO SOME EXTENT, INCREASING THE NUMBER OF BENDS, OR TIGHTENING THE BEND ANGLES IN THE CABLE WILL INCREASE CABLE BACKLASH (LESS BACKLASH IS DESIRABLE, SO MINIMIZE BENDS AND BEND ANGLES IN YOUR INSTALLATION). IN OTHER WORDS, USE LARGE BEND RADII AND SMALL BEND ANGLES TO KEEP YOUR CABLE EFFICIENCY ('BACKLASH') LOW. WARNINGS: (1) DO NOT ADJUST ANY CABLE LENGTH (IE: TURNING THE BALL JOINT OR SPHERICAL ROD END BEARING OR CLEVIS) UNLESS ALL POWER SOURCES, ENGINES, MOTORS, ETC ARE TURNED OFF. (2) CABLES WEAR OUT. AVOID PUTTING CABLES IN APPLICATIONS WHERE A FAILURE TO OPERATE WOULD CAUSE SERIOUS INJURY, DEATH, OR LOSS OF SIGNIFICANT OPERATOR CONTROL OF THE MACHINE OR VEHICLE. MAXIMIZE CABLE LIFE BY USING LARGER CALE SIZES, SHORTER LENGTHS, FEW DEGREES OF BENDS, LOW LOADS, MINIMAL EXPOSURE TO THE ELEMENTS, ETC. (3) USE PHYSICAL STOPS IN YOUR CABLE SYSTEM TO MAKE IT PHYSICALLY IMPOSSIBLE TO EXCEED THE LOAD RATING OR TRAVEL RATING OF THE CABLE. (4) IF THE CABLE LOSSES EFFICIENCY (IE: BECOMES DIFFICULT TO MOVE), REPLACE THE CABLE IMMEDIATELY. (5) DIRT, CONTAMINANTS, TEMPERATURE, MOISTER, AND CYCLES OF USE, ALL EFFECT CABLE LIFE. AVOID EXPOSING THE CABLE TO GASOLINE, OIL, FUELS OF ANY KIND INCLUDING DIESEL, BIODIESEL, WATER, DIRT, FERTILIZER, ROAD SALT, AND CHEMICALS OF ANY KIND. (6) DO NOT ATTEMPT TO LUBRICATE THE CABLE. (7) IF THE CABLE BECOMES FROZEN, OR HAS BEEN FROZEN WITH MOISTURE INSIDE OF IT, THE CABLE MUST BE REPLACED. DO NOT ATTEMPT TO THAW OR DRY OUT CABLES. (8) DO NOT REMOVE THE SEALS OR BOOTS PROVIDED WITH THE CABLE. REPLACE IMMEDIATELY ANY CABLES THAT HAVE LOST OR REMOVED BOOTS AND/OR SEALS. (9) DO NOT ATTEMPT TO MODIFY OR REPAIR A CABLE.
60 inches long
MADE IN THE USA

Specs

Manufacturer part number
J0031748
Vehicle model
J0031748
Vehicle fitment type
Universal
Brand
Steinjager
Automotive specialty part type
Cable
Weight
75 lbs

Current price is $65.60

Price when purchased online

Free shipping
Free 30-day returns

How do you want your item?

Ships to

Arrives by Wed, May 27

Sold and shipped by CSE Offroad Inc

4 stars out of 5, based on 16 seller reviews(4.0)

Report an issue with this seller

Free 30-day returns

About this item

Product details

UNIVERSAL CABLE ASSEMBLY, 10-32 THREADS, 60" LONG, 3" TRAVEL. BOTH ENDS COME WITH BARE THREADS. MADE IN THE USA.

QUANTITY PER PACKAGE: ONE CABLE. PRODUCT NAME: SHIFTER CABLE CABLE LENGTH: 60" THREAD: 10-32 RH CABLE TRAVEL: 3" (COMMENT: THE USABLE STROKE 'TRAVEL' OF A CABLE SHOULD BE CENTERED ON THE TRAVEL RANGE). LINKAGE END: (2) PLATED 10-32 RH JAM NUTS SWIVEL ANGLE: THIS TERM REFERS TO THE SLIGHT MISALIGNMENT ALLOWABLE IN THE PUSH-PULL STROKE OF THE CABLE AS IS ACCOMPLISHED BY THE GUIDE 'TUBE' (THE PIECE BETWEEN THE END OF THE CONDUIT AND THE TRAVEL 'END ROD'). THE MAXIMUM CONICAL MOVEMENT AROUND THIS CENTERLINE SHOULD NOT EXCEED 16°. INSTALLATION: DO NOT BEND ANY OF THE VISIBLE METAL PIECES, OR ANY OF THE INTERSECTIONS OF THESE VISIBLE METAL PIECES; THESE COMPONENTS ARE DESIGNED FOR A PUSH-PULL LOAD ONLY. ONLY INSTALL CABLES WHEN ALL MOTORS, ENGINES, AND POWER SOURCES ARE TURNED OFF. BEND RADII WARNING: EACH CABLE HAS A SPECIFIED MINIMUM BEND RADIUS. FAILURE TO OBSERVE THIS MINIMUM CAN AT A MINIMUM INCREASE THE FORCE IT TAKES TO MOVE THE CABLE, AND AT WORSE, CAN CAUSE THE CABLE TO KINK INSIDE OF THE CONDUIT, WHICH IN TURN CAN CAUSE THE CABLE TO FAIL AND/OR NOT OPERATE PROPERLY. BEND RADIUS MINIMUM: 6" MAXIMUM INPUT LOAD: 75 LBS OPERATING TEMPERATURE RANGES: -65° F TO 225° F COMMON OTHER NAMES FOR THIS PRODUCT: CONTROL CABLE, THROTTLE CABLE, PUSH-PULL CABLE, HEAVY DUTY PUSH PULL CABLE. BACKLASH: THIS TERM IS USED TO DESCRIBE THE MOTION LOST IN MOVING (ACTUATING) THE CABLE. ALTHOUGH THE CABLE DESIGN EFFECTS THIS TO SOME EXTENT, INCREASING THE NUMBER OF BENDS, OR TIGHTENING THE BEND ANGLES IN THE CABLE WILL INCREASE CABLE BACKLASH (LESS BACKLASH IS DESIRABLE, SO MINIMIZE BENDS AND BEND ANGLES IN YOUR INSTALLATION). IN OTHER WORDS, USE LARGE BEND RADII AND SMALL BEND ANGLES TO KEEP YOUR CABLE EFFICIENCY ('BACKLASH') LOW. WARNINGS: (1) DO NOT ADJUST ANY CABLE LENGTH (IE: TURNING THE BALL JOINT OR SPHERICAL ROD END BEARING OR CLEVIS) UNLESS ALL POWER SOURCES, ENGINES, MOTORS, ETC ARE TURNED OFF. (2) CABLES WEAR OUT. AVOID PUTTING CABLES IN APPLICATIONS WHERE A FAILURE TO OPERATE WOULD CAUSE SERIOUS INJURY, DEATH, OR LOSS OF SIGNIFICANT OPERATOR CONTROL OF THE MACHINE OR VEHICLE. MAXIMIZE CABLE LIFE BY USING LARGER CALE SIZES, SHORTER LENGTHS, FEW DEGREES OF BENDS, LOW LOADS, MINIMAL EXPOSURE TO THE ELEMENTS, ETC. (3) USE PHYSICAL STOPS IN YOUR CABLE SYSTEM TO MAKE IT PHYSICALLY IMPOSSIBLE TO EXCEED THE LOAD RATING OR TRAVEL RATING OF THE CABLE. (4) IF THE CABLE LOSSES EFFICIENCY (IE: BECOMES DIFFICULT TO MOVE), REPLACE THE CABLE IMMEDIATELY. (5) DIRT, CONTAMINANTS, TEMPERATURE, MOISTER, AND CYCLES OF USE, ALL EFFECT CABLE LIFE. AVOID EXPOSING THE CABLE TO GASOLINE, OIL, FUELS OF ANY KIND INCLUDING DIESEL, BIODIESEL, WATER, DIRT, FERTILIZER, ROAD SALT, AND CHEMICALS OF ANY KIND. (6) DO NOT ATTEMPT TO LUBRICATE THE CABLE. (7) IF THE CABLE BECOMES FROZEN, OR HAS BEEN FROZEN WITH MOISTURE INSIDE OF IT, THE CABLE MUST BE REPLACED. DO NOT ATTEMPT TO THAW OR DRY OUT CABLES. (8) DO NOT REMOVE THE SEALS OR BOOTS PROVIDED WITH THE CABLE. REPLACE IMMEDIATELY ANY CABLES THAT HAVE LOST OR REMOVED BOOTS AND/OR SEALS. (9) DO NOT ATTEMPT TO MODIFY OR REPAIR A CABLE.
60 inches long
MADE IN THE USA

info:

We aim to show you accurate product information. Manufacturers, suppliers and others provide what you see here, and we have not verified it.

Specifications

Manufacturer part number

J0031748

Vehicle model

J0031748

Vehicle fitment type

Universal

Brand

Steinjager

Warranty

Warranty information

Steinjager has a limited warranty for all parts, for further assisance please reach out via email to info@steinjager.com.

Please be aware that the warranty terms on items offered for sale by third party Marketplace sellers may differ from those displayed in this section (if any). To confirm warranty terms on an item offered for sale by a third party Marketplace seller, please use the 'Contact seller' feature on the third party Marketplace seller's information page and request the item's warranty terms prior to purchase.

Warranty url

https://steinjager.com/shop/warranty

Warnings

WARNING: Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm.