26cc 650W Gas Powered Grass String Trimmer Weed Wacker Cutter Lawn Mower Edger

Starting Method

1. Fill the fuel tank with well-proportioned fuel. (Mixing ratio: 1:20-25 for FB/FC grade engine oil, 1:40-50 for FD grade engine oil)

2. Press the fuel bubble under the carburetor until the fuel bubble is full of fuel.

3. Turn the off switch to the "I" position.

4. Pull the starter rope.

5. When there is a starting response, close the damper and pull the starter rope again.

6. After starting, open the damper.

7. Cycle to accelerate the warm-up machine work.

8. For the first 10 hours of use, the oil mixture ratio should be a little thicker, then follow the normal ratio.

Specification

Color: Red, Silver

Material: PP, Aluminum Alloy, Manganese Steel, Nylon

Assembly Required: Yes

Usage: Side-mounted

Displacement: 26CC

Power: 0.65kw

Rotation Speed: 8500r/min

Engine Type: Single-cylinder Air-cooled 2-stroke Gasoline Engine

Carburetor Type: Diaphragm Carburetor

Gasoline Oil Mixing Ratio: 20-25:1  

Idling Speed: 2800-3200r/min  

Fuel Tank Volume: 1000ml /33.8 Oz

Operating Noise: About 110db

Engine Size: 26*22*27cm/10.24*8.66*10.63in

Product Length: 1.75m/5.74ft

Gross Weight: 8.5kg/18.74 lbs

Package Size:105*25*25 cm/41.34*9.84*9.84 in

Package Included

1 * Weed Wacker

1 * Oil Pot

1 Pair* Goggles 

1 * Funnel

1 * Carrying Strap

1 * English Manual

All Accessories for Installation

 

Notes

The oil mixture ratio should not be wrong or deviated. Please do not use poor-quality motor oil as the matching motor oil.
Please check whether the blade tool is firmly installed before starting the engine, and check whether the blade tool is intact after each work. When starting the engine, personnel need to stay away from 32.81ft or more. Please wear gloves(not included) and goggles during use.    
Please change the engine oil of the new machine every 4 hours of work and every 20 hours of work after 5 times (change the oil when the engine is warm). Please check the oil before each work to see if it is missing and add it to the right position. Fuel needs to be replenished as it is used. Refueling should be kept away from the fire source for more than 49.21ft, and open flame operation such as smoking is prohibited.
The sponge filter inside the air filter needs to be cleaned every 50 hours of work (the cleaning cycle should be shortened when the working environment is dusty), and it can be cleaned with detergent, shampooed with water, and dried before re-installing the air filter.
Before turning off the engine, it should idle for 1-2 minutes to facilitate the natural heat dissipation of the engine.
The blade work head gearbox is filled with grease once every 20 hours of work to provide internal gear lubrication to reduce wear and improve life.
The short flexible shaft and hard shaft inside the connecting disk should be withdrawn after each working cycle, greased and maintained, and then reassembled.
Please check the engine air inlet, cylinder heat sink, and high-pressure package frequently to remove weeds and dust at the air inlet to ensure smooth air ducts and avoid pulling cylinder damage caused by high engine temperature.
If you do not use the machine for more than 10 days, please pour out the oil in the gasoline and engine oil, and press the oil bubble to drain the fuel in the carburetor to avoid damage to the engine caused by oil deterioration.
If the machine is not used for a long time, please put the machine in a dry and ventilated place, and empty the fuel. Please avoid the high-pressure cap, spark plug, etc. from being unable to start due to humidity, rust, and inversion.