SharkBite 1 in. Crimp x 1 in. Dia. PEX Brass Adapter
SharkBite 1 in. Crimp x 1 in. Dia. PEX Brass Adapter
Hero image 0 of SharkBite 1 in. Crimp x 1 in. Dia. PEX Brass Adapter, 0 of 2
RWC

SharkBite 1 in. Crimp x 1 in. Dia. PEX Brass Adapter

|7 ratings

Key item features

  • Brand Name: SharkBite
  • End 1 Diameter: 1 in.
  • End 2 Diameter: 1 in.
  • End 1 Type: Crimp
  • End 2 Type: PEX
  • Material: Brass
  • Product Type: Adapter
  • Packaging Type: Bagged
  • Push to Connect: No
  • Maximum Pressure: 160 psi
  • Maximum Temperature: 200 deg. F
  • Average Lead Content: Lead-Free
  • Number in Package: 1 pk
  • ANSI Certified: Yes
Current price is $11.19
Price when purchased online
  • Free shipping
  • Free 30-day returns

How do you want your item?

How do you want your item?
Columbus, 43215
Arrives by Tue, May 5
|
Sold and shipped by Max Warehouse
4.426002358490566 stars out of 5, based on 10176 seller reviews(4.4)
Report an issue with this seller
Free 30-day returns - in store or online

More seller options (1)

Starting from $11.19

About this item

Product details

Specifications

Warranty

Warnings

Customer ratings & reviews

1.6 out of 5 stars
stars7 ratings7 reviews
How item rating is calculated
  1. 5 stars14% (1)
  2. 4 stars0% (0)
  3. 3 stars0% (0)
  4. 2 stars0% (0)
  5. 1 star86% (6)
Filtered and sorted results would be available on the new 'Customer ratings & reviews' page.
Sort by |

Showing 1-3 of 7 reviews

Oct 7, 2020
Stevenson A
5 out of 5 stars review

Bye-Bye Copper

I've used these several times to as a DIYer. Clean your copper and the adapter, use ample flux and get the joint hotter than normal. Never had a failure.

Review from sharkbite.com
Helpful?48A0KGITLVCJ486501150
Dec 28, 2018
Nathan W
1 out of 5 stars review

No Good - Won't Solder

Similar to other reviewers here, I was unable to get solder to stick to these. Doesn't have anything to do with cleaning, prep, or materials (solder, flux, etc) as I used many other fittings in my system (with identical installation) and ONLY these gave me trouble. EVERYONE of these wouldn't work. Too bad. First Sharkbite product I've purchased which I'm not satisfied with. Interestingly enough, these have a larger ID than the other sweat fittings I purchased Most fittings have enough friction on the pipe to stay in place while you sweat them on. These things are just loose enough that they will slide off the pipe.

Review from sharkbite.com
Helpful?48A0KGITLVCJ486501150
Dec 19, 2016
Tony G
1 out of 5 stars review

Cannot get solder to stick

I have had the same issue as many folks here. I had an issue with four of these where the solder would not stick. I am a homeowner but have done thousands of sweating copper pipes and never had an issue like this. The initial three I replaced with other ones and was able to complete. Last one just did yesterday wasting over two hours and a visit to HD was completed only by switching to the threaded SharkBite fitting to a copper threaded fitting that I was able to sweat in less than a minute. I am a bit concerned about the SharkBite fittings left that were soldered that they may start leaking one day, so will need to keep an eye or totally remove all of them.

Review from sharkbite.com
Helpful?48A0KGITLVCJ486501150
reply from Technical Support

Good morning, We apologize for the difficulty you experienced with the Sweat Adapters. We've tested these fittings and if the pipe and fitting are properly cleaned there should be no issue soldering. If you would like to send the product back to us for testing we would be happy to replace, also if you could share some more details with on us it would be helpful in identifying possible solutions to your issue. Our customer service number is 1-877-700-4242 open M-F 8am to 6pm, please give us a call and we'd be happy to assist!