Hero image 0 of BEP Pro Installer 400A Dual Bank Control Switch - MC10 [772-DBC], 0 of 5

BEP

BEP Pro Installer 400A Dual Bank Control Switch - MC10 [772-DBC]

(No ratings yet)

Key item features

Pro Installer 400A Dual Bank Control Switch - MC10Another addition to our multi award winning Pro Installer EZ Mount range, the innovative Dual Bank Control switch is like 3 switches in one, House, Start, and Emergency Parallel. Offering easy intuitive control for the boater, the Dual Bank Control switch features a unique isolated-On position which allows use of house loads and VHF radio if the engine needs to be electrically isolated, or allows the engine to be isolated during servicing while still providing power to house loads (for lighting, stereo, fridge etc). For boats or vehicles with single Engine and House battery bank, Dual Bank Control allows the use of optimized battery banks for their respective loads; an appropriately sized deep cycle bank for House loads, and thin plate starting batteries for the Engine. Further, sensitive electronics are isolated from starter motor induced voltage spikes because House and Engine loads are separated during normal operation, unlike Selector battery switches. As easy as 1, 2, 3, these revolutionary EZ Mount battery switches allow you to wire from the front for the easiest surface mounting. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze.
Tested to UL1107 ignition protection, CE
Tinned copper 10mm (3/8 inch) studs
Stainless steel washers and nuts
Fiber reinforced plastics
400A Continuous / 600A 5 minutes Intermittent / 1500A 10 seconds Cranking (cable size to achieve ratings 120mm}, 4/0, smaller cable size will reduce the Amp rating)
Waterproof to IP67
Same interconnection height as Pro Installer
Removable knob allows isolation during servicing
3 removable side plates for protection
Industry standard 3.85 x 3.85 inch footprint
For surface mounting only
Each Pro Installer battery switch is fully tested for pressure sealing, rotation force and electrically load testedSpecificationsMounting: Surface, Rear or FrontVoltage: 48v DC (for 12-48v systems, both banks must be same voltage)Rating: 400 Cont / 600 Inter / 1500 CrankDims: 3.85" x 3.85" x 3.62"Operation: 1, 1/2, Parallel, OffStud: 4x 10 mm (3.8")WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications:
AFD: No
Lockable: No
Positions: 1-1/2-Parallel-Off
Continuous Amperage: 400a
Box Dimensions: 4"H x 7"W x 8"L WT: 1.2 lbs
UPC: 843687007807Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)

Specs

Boat accessory type
Battery Switch
Brand
BEP
Features
LED Lighting
Material
Other Material
Size
3.85" x 3.85" x 3.62"
Color
Multicolor

Current price is $89.99

Price when purchased online

Out of stock

How do you want your item?

Out of stock

About this item

Product details

New Pro Installer 400a Dual Bank Battery Switch marinco 772-dbc Parallel 1 Both : This innovative Patent Pending switch combines the functions of 3 battery switches into one House Start and Emergency Parallel to intuitively manage 2 battery banks and 2 loads. A unique safety position isolates one load e.g. House On Start Off in case of engine malfunction so an emergency radio call can still be made. Significant savings in both space and installation cost can be made without compromising functionality or safety.

Pro Installer 400A Dual Bank Control Switch - MC10Another addition to our multi award winning Pro Installer EZ Mount range, the innovative Dual Bank Control switch is like 3 switches in one, House, Start, and Emergency Parallel. Offering easy intuitive control for the boater, the Dual Bank Control switch features a unique isolated-On position which allows use of house loads and VHF radio if the engine needs to be electrically isolated, or allows the engine to be isolated during servicing while still providing power to house loads (for lighting, stereo, fridge etc). For boats or vehicles with single Engine and House battery bank, Dual Bank Control allows the use of optimized battery banks for their respective loads; an appropriately sized deep cycle bank for House loads, and thin plate starting batteries for the Engine. Further, sensitive electronics are isolated from starter motor induced voltage spikes because House and Engine loads are separated during normal operation, unlike Selector battery switches. As easy as 1, 2, 3, these revolutionary EZ Mount battery switches allow you to wire from the front for the easiest surface mounting. With their shared interconnection height, EZ-Mount battery switches "cluster" directly with the Pro Installer Busbar Range, resulting in the fastest, most compact installations. Optimized cable access makes installation a breeze.
Tested to UL1107 ignition protection, CE
Tinned copper 10mm (3/8 inch) studs
Stainless steel washers and nuts
Fiber reinforced plastics
400A Continuous / 600A 5 minutes Intermittent / 1500A 10 seconds Cranking (cable size to achieve ratings 120mm}, 4/0, smaller cable size will reduce the Amp rating)
Waterproof to IP67
Same interconnection height as Pro Installer
Removable knob allows isolation during servicing
3 removable side plates for protection
Industry standard 3.85 x 3.85 inch footprint
For surface mounting only
Each Pro Installer battery switch is fully tested for pressure sealing, rotation force and electrically load testedSpecificationsMounting: Surface, Rear or FrontVoltage: 48v DC (for 12-48v systems, both banks must be same voltage)Rating: 400 Cont / 600 Inter / 1500 CrankDims: 3.85" x 3.85" x 3.62"Operation: 1, 1/2, Parallel, OffStud: 4x 10 mm (3.8")WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Specifications:
AFD: No
Lockable: No
Positions: 1-1/2-Parallel-Off
Continuous Amperage: 400a
Box Dimensions: 4"H x 7"W x 8"L WT: 1.2 lbs
UPC: 843687007807Quick Guide (pdf)Owner's Manual (pdf)Brochure (pdf)