Hero image 0 of TOOL1SHOoo High-pressure Diaphragm Pump 5 GPM 12V DC Self-priming RV Water Pump Auto Switch, 0 of 7

TOOL1SHOoo High-pressure Diaphragm Pump 5 GPM 12V DC Self-priming RV Water Pump Auto Switch

(No ratings yet)

Key item features

Iron Plate Mounting Feet: The water pump's mounting feet are made of iron, which is strong and durable. The iron mounting feet can significantly reduce the working noise and improve the working environment. Moreover, the surface of the iron plate is galvanized, which makes it less likely to rust and corrode.
Filter: The filter can effectively filter out debris and other particles from the pump. And its detachable design makes it easy to clean and assemble.
PA Pump Head: The head of this pump is made of PA, whose excellent toughness and fatigue resistance can extend the service life of the pump.
Interface Protective Cover: The water pump is equipped with a protective cover at the interface, which can effectively protect the interface from being damaged in transit.
Application：The water pump is suitable for filling equipment, agricultural irrigation, dishwashers, spray equipment, etc.
Notes
1. When the pump is working, it is necessary to ensure smooth drainage of the pump to avoid holding the pump and causing damage to the pressure switch.
2. If you hear the switch ticking in operation, please turn off the pump immediately and adjust the pressure appropriately.
3. The motor has a slight waterproof function, splashed with a little water do not need to worry too much (dry can be), but the pump motor is strictly prohibited to immerse in water. If the pump is placed in the open air, it should be protected with a cover to avoid water splashing into the motor, causing power failure, leakage, or motor damage.
4. The water inlet must be installed with a filter device, so as not to inhale the liquid with impurities, otherwise, it will easily block the pump, which will result in lower pressure, smaller flow, and even no water pumping. It is strictly forbidden to use this machine without a filter, and the density of the filter is better than 50 mesh (impurities will cause damage to the pump).
5. The water pump works intermittently. Please note that it does not work for 24 hours. Please disconnect the connection between the motor pump and the power supply when it is not used for a long time or suspended in the middle of the use.
6. The pump has a pressure switch adjustment function. You can properly adjust the pressure according to your actual needs. If the pressure is too small, the switch is easy to start and stop frequently resulting in burning. If the pressure is too large, the switch is less likely to play a role, which results in the pump can not being properly closed.
7. After using in winter, you need to drain the water in the pump and pipeline, otherwise it is easy to freeze and break the pump (only for some cold icing place).
8. The pump has been tested before leaving the factory, so the user should not disassemble it. Before use, please confirm the power supply, power parameters need to be consistent with the motor pump input parameters.
9. The correct installation method should be with the pump head facing down or lying flat.
10. Please allow the slight color difference caused by the shooting light and 1-3cm error due to manual measurement. Please make sure you do not mind before you order.
When the pump is working, it is necessary to ensure smooth drainage of the pump to avoid holding the pump and causing damage to the pressure switch.
If you hear the switch ticking in operation, please turn off the pump immediately and adjust the pressure appropriately.
The motor has a slight waterproof function, splashed with a little water do not need to worry too much (dry can be), but the pump motor is strictly prohibited to immerse in water. If the pump is placed in the open air, it should be protected with a cover to avoid water splashing into the motor, causing power failure, leakage, or motor damage.
The water inlet must be installed with a filter device, so as not to inhale the liquid with impurities, otherwise, it will easily block the pump, which will result in lower pressure, smaller flow, and even no water pumping. It is strictly forbidden to use this machine without a filter, and the density of the filter is better than 50 mesh (impurities will cause damage to the pump).
The water pump works intermittently. Please note that it does not work for 24 hours. Please disconnect the connection between the motor pump and the power supply when it is not used for a long time or suspended in the middle of the use.
The pump has a pressure switch adjustment function. You can properly adjust the pressure according to your actual needs. If the pressure is too small, the switch is easy to start and stop frequently resulting in burning. If the pressure is too large, the switch is less likely to play a role, which results in the pump can not being properly closed.
After using in winter, you need to drain the water in the pump and pipeline, otherwise it is easy to freeze and break the pump (only for some cold icing place).
The pump has been tested before leaving the factory, so the user should not disassemble it. Before use, please confirm the power supply, power parameters need to be consistent with the motor pump input parameters.
The correct installation method should be with the pump head facing down or lying flat.
Please allow the slight color difference caused by the shooting light and 1-3cm error due to manual measurement. Please make sure you do not mind before you order.
TOOL1SHOoo COLLECTION is a professional tool and equipment company aiming to provide quality products and services. If you have any problems, please feel free to contact us and we will reply to your in 24 hours.

Specs

Gallons per minute
4.99 GPM
Plumbing pump type
Diaphragm Pump
Brand
TOOL1SHOoo
Features
Automatic
Volts
110 V
Assembled product height
4.1 in

Current price is $72.83

Price when purchased online

Free shipping
Free 30-day returns

Walmart Protection Plan by Allstate

(Only one option can be selected at a time)

2-Year Plan - $8.00

3-Year Plan - $12.00

How do you want your item?

Columbus, 43215

Arrives between May 11 - May 13

Sold and shipped by TOOL COLLECTION-4340

4.086956521739131 stars out of 5, based on 46 seller reviews(4.1)

Report an issue with this seller

Free 30-day returns - in store or online

About this item

Product details

【Product introduction】

This TOOL1SHOoo water pump uses a pure copper motor to provide it with powerful and stable power.With a rated head of 124.67 feet,it can water farmland and vegetation over long distances,saving time and effort on manual transportation.The pump's 4.99 GPM flow rate makes pumping water even faster.

【Specifications】

Pump Body Material:Engineering Plastic
Color:Blue
Valve Material:EPDM
Diaphragm Material:TPE
Pump Head Material:PA
Valve Seat Material:POM Plastic
Voltage:110V
Current:2.5A
Power Frequency:50HZ
Rated Power:275W
Connection Method:Thread
Voltage Fluctuation Range:+-10%of rated value
Volume of Solid Impurities In the Medium:<=0.1
Media Containing Solid Impurities In the Particles:<0.2mm/0.004in
Stop Pressure:55PSI/3.8BAR
Control Mode:Pressure/Return Switch
Wiring Method:Double-core Wire
Ambient Temperature:Less than or Equal to 50℃
Medium Temperature:0-65℃
Medium PH:5.0-10
Rated Flow Rate:18.9L/min
Rated Head:38m/124.67ft
Inlet Size:1/2in-14 Male Threaded Interface
Pressure Adjustment Range:1-4.1kg/2.20-9.03lbs
Product Size:23.3*12.6*10.9cm/9.2*5*4.3in
Package Size:29.9*14.6*12.8cm/11.77*5.74*5.03in
Net Weight:2.80kg/6.17 lbs
Gross Weight:2.84kg/6.26lbs

【Pressure Switch Adjustment Method】

Open the pressure switch cover with a screwdriver.
Locate the internal hexagonal screw hole in the center of the switch.
Turn it clockwise to increase the pressure,and counterclockwise to decrease the pressure.

【Operating Instructions】

Connect the pump with the inlet and outlet pipes,and make sure that the inlet and outlet pipes are tightly connected,otherwise,it will cause low pressure,no water suction,water leakage,and other problems.
Install a filter at the inlet end.The density of filtration is better than 50 mesh.
The pump is connected to the power supply,and the output parameters of the connected power supply must meet the input requirements of the motor.
Turn on the power,and the pump starts to run out of water for 5-10 seconds.Drain the air in the pump and pipeline.When the water is stable,turn off the power temporarily.Then connect the water gun,faucet,shower,and other related tools.
When you stop using,just turn off the water outlet faucet.The water pump has a pressure switch automatic start/stop function.You just open the faucet for the next use.

【Package Included】

1*Water Pump
1*Strainer
2*Connectors

【Key features】

Automatic Start/Stop:The water pump features an automatic start/stop design,which allows the pump to turn on/off automatically when you turn the faucet on/off.The auto start/stop design is easy to operate and reduces power consumption.
Pure Copper Motor:The coil of the motor is made of pure copper,which is more stable and durable because it has less resistance compared to aluminum.
Remote Irrigation:With a maximum head of 124.67 feet,the water pump can water farmland and vegetation over long distances,saving time and effort in manual transportation.
Sturdy and Durable:The water pump features a built-in bypass return design.When the actual flow rate used is less than the pump output,the pressure relief cycle is activated.This effectively protects the pressure switch to extend the product's life.
Standard Fittings:The water pump uses 1/2"standard fittings to fit most equipment sizes.This is easy to install and use.

Iron Plate Mounting Feet: The water pump's mounting feet are made of iron, which is strong and durable. The iron mounting feet can significantly reduce the working noise and improve the working environment. Moreover, the surface of the iron plate is galvanized, which makes it less likely to rust and corrode.
Filter: The filter can effectively filter out debris and other particles from the pump. And its detachable design makes it easy to clean and assemble.
PA Pump Head: The head of this pump is made of PA, whose excellent toughness and fatigue resistance can extend the service life of the pump.
Interface Protective Cover: The water pump is equipped with a protective cover at the interface, which can effectively protect the interface from being damaged in transit.
Application：The water pump is suitable for filling equipment, agricultural irrigation, dishwashers, spray equipment, etc.
Notes
1. When the pump is working, it is necessary to ensure smooth drainage of the pump to avoid holding the pump and causing damage to the pressure switch.
2. If you hear the switch ticking in operation, please turn off the pump immediately and adjust the pressure appropriately.
3. The motor has a slight waterproof function, splashed with a little water do not need to worry too much (dry can be), but the pump motor is strictly prohibited to immerse in water. If the pump is placed in the open air, it should be protected with a cover to avoid water splashing into the motor, causing power failure, leakage, or motor damage.
4. The water inlet must be installed with a filter device, so as not to inhale the liquid with impurities, otherwise, it will easily block the pump, which will result in lower pressure, smaller flow, and even no water pumping. It is strictly forbidden to use this machine without a filter, and the density of the filter is better than 50 mesh (impurities will cause damage to the pump).
5. The water pump works intermittently. Please note that it does not work for 24 hours. Please disconnect the connection between the motor pump and the power supply when it is not used for a long time or suspended in the middle of the use.
6. The pump has a pressure switch adjustment function. You can properly adjust the pressure according to your actual needs. If the pressure is too small, the switch is easy to start and stop frequently resulting in burning. If the pressure is too large, the switch is less likely to play a role, which results in the pump can not being properly closed.
7. After using in winter, you need to drain the water in the pump and pipeline, otherwise it is easy to freeze and break the pump (only for some cold icing place).
8. The pump has been tested before leaving the factory, so the user should not disassemble it. Before use, please confirm the power supply, power parameters need to be consistent with the motor pump input parameters.
9. The correct installation method should be with the pump head facing down or lying flat.
10. Please allow the slight color difference caused by the shooting light and 1-3cm error due to manual measurement. Please make sure you do not mind before you order.
When the pump is working, it is necessary to ensure smooth drainage of the pump to avoid holding the pump and causing damage to the pressure switch.
If you hear the switch ticking in operation, please turn off the pump immediately and adjust the pressure appropriately.
The motor has a slight waterproof function, splashed with a little water do not need to worry too much (dry can be), but the pump motor is strictly prohibited to immerse in water. If the pump is placed in the open air, it should be protected with a cover to avoid water splashing into the motor, causing power failure, leakage, or motor damage.
The water inlet must be installed with a filter device, so as not to inhale the liquid with impurities, otherwise, it will easily block the pump, which will result in lower pressure, smaller flow, and even no water pumping. It is strictly forbidden to use this machine without a filter, and the density of the filter is better than 50 mesh (impurities will cause damage to the pump).
The water pump works intermittently. Please note that it does not work for 24 hours. Please disconnect the connection between the motor pump and the power supply when it is not used for a long time or suspended in the middle of the use.
The pump has a pressure switch adjustment function. You can properly adjust the pressure according to your actual needs. If the pressure is too small, the switch is easy to start and stop frequently resulting in burning. If the pressure is too large, the switch is less likely to play a role, which results in the pump can not being properly closed.
After using in winter, you need to drain the water in the pump and pipeline, otherwise it is easy to freeze and break the pump (only for some cold icing place).
The pump has been tested before leaving the factory, so the user should not disassemble it. Before use, please confirm the power supply, power parameters need to be consistent with the motor pump input parameters.
The correct installation method should be with the pump head facing down or lying flat.
Please allow the slight color difference caused by the shooting light and 1-3cm error due to manual measurement. Please make sure you do not mind before you order.
TOOL1SHOoo COLLECTION is a professional tool and equipment company aiming to provide quality products and services. If you have any problems, please feel free to contact us and we will reply to your in 24 hours.

info:

We aim to show you accurate product information. Manufacturers, suppliers and others provide what you see here, and we have not verified it.

Specifications

Gallons per minute

4.99 GPM

Plumbing pump type

Diaphragm Pump

Brand

TOOL1SHOoo

Features

Automatic

Warranty

Warranty information

Please be aware that the warranty terms on items offered for sale by third party Marketplace sellers may differ from those displayed in this section (if any). To confirm warranty terms on an item offered for sale by a third party Marketplace seller, please use the 'Contact seller' feature on the third party Marketplace seller's information page and request the item's warranty terms prior to purchase.