Oil Level Sensor Fuel Gauge 0-190Ohm Fuel Level Gauge Meter Fuel Level Sensor Fuel Gauge 52Mm For Boat Car Fuel Level Sensors

Features:
* The fuel sensor unit is made of heavy-duty stainless steel. The advantages of this fuel tank sensor unit are reed switch, durability and reliability, and the output signal is stable. The fuel tank does not need to be adjusted, accurately indicating the fuel level of the tank.
* The fuel level sensor is suitable for marine, automotive, truck, bus and marine fields.
* The fuel gauge combined with the fuel sensor unit makes vehicle operation easier and avoids signal mismatch.
* The fuel/water level sensor is suitable for US standard output 240-33 ohms (240 ohms when empty and 33 ohms when full).
* The fuel gauge is made of 316 stainless steel frame, IP67 waterproof and dustproof curved glass lens. Diameter: 2-1/16 inches (52 mm), working voltage: 12-24V.
* Easy to install, all accessories are included in the package, no other accessories are required. The package contains 1 fuel gauge, 1 marine fuel sensor, 1 washer, 5 screws and 1 instruction manual. SAE 5-hole mounting pattern for easy installation and connection. Well-written and illustrated instructions are simple to understand and easy to follow.
* Avoid the sensor from hitting the bottom of the tank, the length of the sensor should be 1 inch (25 mm) less than the depth of the tank.

Specifications:
Part Name: Oil Level Sensor + Fuel Gauge
Oil Level Sensor Material: Stainless Steel
Color: As shown in the picture
Oil Level Sensor Size (Optional): 100mm, 125mm, 150mm, 175mm, 200mm, 225mm, 250mm, 275mm, 300 mm, 325mm, 350mm, 375mm, 400mm, 425mm, 450mm, 475mm, 500mm, 550mm
Sensor Specifications: (as below)
- for Protection Grade: IP67
- Resolution Range: 21mm
- Assembly: SAE Standard 5 Holes
- Alarm Switch Rated Current: 500mA
- Operating Temperature: -40 to 85 degrees Celsius
- Suitable for Fuel Level Gauge and Water Level Gauge
- Installation: 5 pieces of M5 screws and 2 mm thick gasket
- Output Signal: 0~190 ohms (European Standard),
Note;
- Empty oil level: 0 ohm/240 ohm
- Full oil level: 190 ohm/33 ohm
- When the oil/water level is empty, there will be a gap of 3-15 mm between the sensor float and the bottom of the sensor. the sensor can work normally, thank you~
- When the oil/water level is full, there will be a gap of 3-15 mm between the sensor float and the top of the sensor. the sensor can work normally, thank you~
Fuel gauge specifications (as follows)
Fuel gauge material: PC polycarbonate
- Size: about 8x8x7cm/3.15x3.15x2.76 inches
- Working voltage: 9-32V
- Working current ≤60mm
- Working temperature: -30~+75°C
- Meter diameter: 52mm / 2 inches
- Light: When the fuel level is below 13%, the light will flash.
The correct connection is: (as follows)
- The yellow wire of the meter does not need to be connected (if your sensor signal is 0~190ohm)
- The black wire of the meter is connected to the negative pole of the power supply,
- The red wire of the meter is connected to the positive pole of the power supply,
- Connect the blue wire of the meter to the brown wire of the sensor,
- The blue wire of the sensor is connected to the negative pole of the power supply.

Package Contents:
1 x Fuel Level Sensor
1 x 52mm Fuel Level Meter

Note:
1.The real color of the item may be slightly different from the pictures shown on website caused by many factors such as brightness of your monitor and light brightness.
2.Please allow slight manual measurement deviation for the data.