Hero image 0 of 100A Digital Lcd Double Pulse Encoder Spot Welder Machine Time Control Board,1 * Main Board 1 * Display Board 1 * Cable,green, 0 of 7
100A Digital Lcd Double Pulse Encoder Spot Welder Machine Time Control Board,1 * Main Board 1 * Display Board 1 * Cable,green
(No ratings yet)
Key item features
- The solder joint is not secure or soldered: adjust welding time and power until satisfactory results are achieved.Can be set to save the last operation, the module double pulse trigger, turn off any set of trigger time, you can change double pulse to single pulse trigger.The main board and the display operation panel are separated, and the outer casing can be flexibly assembled.
- With grid voltage compensation, the output of compensation can be automatically adjusted according to the change of power supply, and the electric voltage of about 1 second can be displayed when triggered, so that the effective heat of welding is consistent with the welding parameters, and the welding spot is uniform.
- Pay attention to the safe use of the high voltage part during installation. When the usage frequency and power are high, silicon control rectifier requires external radiator to disspate heat.The power of the module driving load depends on the power of silicon control rectifier (SCR). BAT41 (40A) can carry a microwave oven transformer, BAT100 (100A) can carry two microwave oven , and the recommended one for Loop transformer is 100A.
- III. Usage method:Voltage calibration:The module has voltage compensation function, so the voltage calibration must be carried out when the first machine is installed, and in , as long as the module power transformer is not replaced, there is no need to recalibrate. Of course, when you feel that the display voltage is wrong and it can be calibrated. The following are the mains voltages that are not calibrated and displayed during operation
- Precautions for use:This module DIY needs to have certain electrician knowledge, if you are complete freshman, please refer to the electrician's knowledge before you . Do not know the welding time and power of the welded parts, it is recommended that the welding time and power be adjusted from small to upper to avoid damage to the welding pen.Fault cause and troubleshooting,The electricity supply does not match the actual electricity voltage: re-voltage calibration.
Specs
Current price is USD$21.49
Price when purchased online
- Free shipping
Free 30-day returns
How do you want your item?
Columbus, 43215
Arrives between Apr 29 - May 4
|
Sold and shipped by illusory
4.111111111111111 stars out of 5, based on 9 seller reviews(4.1)9 seller reviews
Free 30-day returns
About this item
Product details
DIY or simple battery welder development welding.
Welding of a single battery or battery pack.
Multi-group data 12864 visual display, intuitive operation, convenient, single encoder parameter adjustment can make the operation simple and fast.
With 0-9999 welding counting function, with 5 groups of sample storage parameters, can be stored even the electricity power is off, the number of wleding could be seen just by a glance.
Time input 0-99 cycle (1 cycle is 20ms, for example, the adjustment value is 50, which is the welding time 1 second.), the stop time between 2 weldings is 0-99 cycles (1 cycle is 20ms, such as interval value 50, It is the interval of 1 second.) adjustable. Welding strength 30%-99% is adjustable.
The module can isolate the strong and weak electricity by optical coupling, and design a reliable circuit for zero-crossing detection and voltage detection to the accurate phase shift of silicon control rectifier (SCR), which can be compatible with 40A-100A bidirectional silicon control rectifier (SCR).
9-12 V AC power input (using AC , other such as DC, can cause zero-crossing detection failure, can not trigger.)
colour:green
Material:Metal + PC
Package Contents:
1 * Main Board
1 * Display Board
1 * Cable
Welding of a single battery or battery pack.
Multi-group data 12864 visual display, intuitive operation, convenient, single encoder parameter adjustment can make the operation simple and fast.
With 0-9999 welding counting function, with 5 groups of sample storage parameters, can be stored even the electricity power is off, the number of wleding could be seen just by a glance.
Time input 0-99 cycle (1 cycle is 20ms, for example, the adjustment value is 50, which is the welding time 1 second.), the stop time between 2 weldings is 0-99 cycles (1 cycle is 20ms, such as interval value 50, It is the interval of 1 second.) adjustable. Welding strength 30%-99% is adjustable.
The module can isolate the strong and weak electricity by optical coupling, and design a reliable circuit for zero-crossing detection and voltage detection to the accurate phase shift of silicon control rectifier (SCR), which can be compatible with 40A-100A bidirectional silicon control rectifier (SCR).
9-12 V AC power input (using AC , other such as DC, can cause zero-crossing detection failure, can not trigger.)
colour:green
Material:Metal + PC
Package Contents:
1 * Main Board
1 * Display Board
1 * Cable
- The solder joint is not secure or soldered: adjust welding time and power until satisfactory results are achieved.Can be set to save the last operation, the module double pulse trigger, turn off any set of trigger time, you can change double pulse to single pulse trigger.The main board and the display operation panel are separated, and the outer casing can be flexibly assembled.
- With grid voltage compensation, the output of compensation can be automatically adjusted according to the change of power supply, and the electric voltage of about 1 second can be displayed when triggered, so that the effective heat of welding is consistent with the welding parameters, and the welding spot is uniform.
- Pay attention to the safe use of the high voltage part during installation. When the usage frequency and power are high, silicon control rectifier requires external radiator to disspate heat.The power of the module driving load depends on the power of silicon control rectifier (SCR). BAT41 (40A) can carry a microwave oven transformer, BAT100 (100A) can carry two microwave oven , and the recommended one for Loop transformer is 100A.
- III. Usage method:Voltage calibration:The module has voltage compensation function, so the voltage calibration must be carried out when the first machine is installed, and in , as long as the module power transformer is not replaced, there is no need to recalibrate. Of course, when you feel that the display voltage is wrong and it can be calibrated. The following are the mains voltages that are not calibrated and displayed during operation
- Precautions for use:This module DIY needs to have certain electrician knowledge, if you are complete freshman, please refer to the electrician's knowledge before you . Do not know the welding time and power of the welded parts, it is recommended that the welding time and power be adjusted from small to upper to avoid damage to the welding pen.Fault cause and troubleshooting,The electricity supply does not match the actual electricity voltage: re-voltage calibration.
info:
We aim to show you accurate product information. Manufacturers, suppliers and others provide what you see here, and we have not verified it. Â
Specifications
Brand
Unbranded
Manufacturer
China
Warranty
Warranty information
Please be aware that the warranty terms on items offered for sale by third party Marketplace sellers may differ from those displayed in this section (if any). To confirm warranty terms on an item offered for sale by a third party Marketplace seller, please use the 'Contact seller' feature on the third party Marketplace seller's information page and request the item's warranty terms prior to purchase.
Customer ratings & reviews
0 ratings|0 reviews
This item does not have any reviews yet
