WIKCOVER 4000W MPPT Solar Charge Controller 100A 12V 24V 36V 48V USB Battery for Solar Panels

WIKCOVER 4000W MPPT Solar Charge Controller 100A 12V 24V 36V 48V USB Battery PV Regulator for Solar Panels

Product Features:

• LCD Display:
  Large-size liquid crystal display, support battery working status display, solar panel working status display, mode control display, load output status and parameter display, normal and fault status display.
• 7 Operating Modes:
  charging mode, light control mode, light control + delay control mode, general control mode, manual control mode, timing control mode and test mode, of which the test mode is only used for factory testing.
• 4 Kinds Of Voltage Automatic Recognition:
  Automatically identify DC12V, DC24V, DC36V, and DC48V.
• Large Section Connection Port:
  The product uses a large section, large spacing of the wiring port, can be installed 16mm wire, 7mm line spacing increases the insulation performance and installation reliability, effectively reduce the current and voltage drop while reducing loss.
• Dual USB Charging Port:
  The solar charging controller adopts dual USB charging port design, which can charge two devices at the same time, and supports most USB interface devices, such as mobile phones, tablets, PS game consoles, etc.
• Thickened Aluminum Alloy Heat Sink:
  With MOS tube locking heat sink design, heat dissipation is more uniform, do not worry about the temperature rise caused by MOS tube, powerful heat dissipation ability can work normally under 55℃ environment, while preventing overcharge, overvoltage, DC output low voltage, high voltage protection and reverse polarity protection functions.
• Product Specification
  Condition: 100% Brand New
  Maximum Charging Current: 100A±10%
  Maximum Current Load: 100A±10%
  Maximum Input Voltage: 15V-23V (12V), 30V-45V (24V), 45V-69V (36V), 60V-90V (48V)
  Maximum Input Power: 1000W (12V), 2000W (24V), 3000W (36V), 4000W (48V)
  Output Voltage: DC12V/24V/36V/48V; DC5V/1.5A × 2USB
  Support Battery: Lithium Battery And Lead-Acid Battery
  Operating Temperature: -25℃~55℃
  Heat Dissipation Mode: Radiator Self-Cooling
  Charging Mode: Focus On MPPT Modulation Charging
  Number Of Working Modes: Seven
  Maximum Input Voltage Of Photovoltaic Panel: ≤100V
  Low Battery Default Shutdown Voltage: 9.5V(12V), 19V(24V), 28.5V(36V), 38V(48V) (The default value can be modified according to the application)
  Battery Charging Default Floating Charge Voltage: 14.2(12V), 28.4V(24V), 42.6V(36V), 56.8V(48V) (The default value can be modified according to the application)
  Overtemperature Protection: MOS Tube Temperature Above 85℃ Protection
  Protection Function: Prevent Overcharge, Overvoltage/DC Output Low Voltage, High Voltage Protection, Reverse Polarity Protection, Etc
  Material: Black Plastic Shell + Aluminum Cooling Base Plate
  
  Attention Please
  1. Please allow manual measurement error of 1-5mm. Make sure you don't mind before you buy.
  2. Due to lighting effects, brightness contrast Settings of the display, etc., there may be some slight differences in the hue of the picture and the actual item, please make sure you don't mind.
  3. Wiring instructions: In order to correctly identify the voltage, the controller should ensure that:
  ① 12V battery voltage is higher than 10V
  ② 24V battery voltage is higher than 20V
  ③ The 36V battery voltage is higher than 30V
  ④ The 48V battery voltage is higher than 40V
  The controller is connected to the battery first, then to the photovoltaic panel, and then to the DC load.