I have 300000 miles on my Jeep and the motor flush works great every other oil change.
About This Item
MOTOR MEDIC 5-Minute Motor Flush, 32 oz:
- Improves oil circulation
- 5-minute engine flush does not cause damage to seals
- No bearing wear
- Cleans engine in 5 minutes
- Recommended before each oil change
- Helps remove engine deposits
- Quick and easy to use
- Suitable for use in a wide range of vehicles
- From the makers of Gunk
proposition 65 reasons:titanium dioxide, other chemicals
WARNING: This product may contain chemicals known to the State of California to cause cancer andbirth defects or other reproductive harm. www.p65warnings.ca.gov
Instructions: . Important: For engines equipped with oil-cooled turbochargers, follow all label use instructions exactly. For best cleaning results in turbocharged gasoline and turbo-diesel engines, use Motor MedicÂ® Synthethic Motor Flush (part number MFD1). During the motor cleaning process do not operate the engine for longer than 5 minutes, never above idle rpm's, and never with the vehicle in motion or the engine under load until after you have drained the old oil and Motor Flush from the crankcase and replaced it with new oil and filter. Directions: 1. Check to make certain oil in crankcase is up to safe level. 2. Add Motor Medic Motor Flush to cold engine before changing oil and filter. Idle engine at normal speed for 5 minutes. Do Not Drive Vehicle Motor Medic Motor Flush will circulate throughout the entire lubricating system of your engine dissolving sludge, gums and varnishes from engine and oil pan. It also frees sticking valves and rings. 3. Drain crankcase and remove oil filter. Replace drain plug and install new oil filter. Note: On engines with over 75,000 miles or excessive deposits, remove and clean the oil pan to minimize the risk of engine damage. 4. Refill crankcase with oil. Note: Extremely dirty engines may require repeat treatment. Follow directions 1 to 4. Use before every oil change takes 5 minutes
Packaging requirements for returns
|Manufacturer Part Number|
RSC Chemical Solutions
|Assembled Product Dimensions (L x W x H)|
8.60 x 4.20 x 3.10 Inches
Customer reviews & ratings
Great engine cleaner
Have 200k on my Chevy trailblazer 05 it was sluggish in accelerating and check engine light would intermittently come on especially when cold but went away when it warmed up. Bought this and before I poured it I drained about a quart of oil out of the oil pan, and sealed back, added the whole 1 quart to the block and ran for 7 min, and completely drained it and changed my oil, once the oil was in with a new filter the check engine light was on and after about 2 min of it at idle it went off. I feel like it has restored more horses power in the engine along with the oil pressure gauge staying steady before it would go up to 65 psi now highest is 50 psi, also with a visual inspection I saw inside the valve cover was a lot cleaner and took a lot of thick particles away, I would highly recommend it
It Worked for Me!
The motor in a 2000 GMC Sierra with 195,000 miles began having valve/lifter noise from the right side of the engine on start up. I was going to do an early oil change, 2000 miles, and looked for a product to clean the engine as well. Found Motor Medic after researching and used as directed. After the oil change, with Castrol Synthetic, I took a 200 mile trip and the following morning there was none of the noise I previously experienced. I personally would not use it with dirty oil as that would kind of defeat its purpose. I will do another short change after about 2000 miles, as there is a residual amount of the Motor Medic left in the engine.
I have an 08 Sierra with just over 200K on the odometer, two days ago I started hearing a tapping from the engine. A friend who knows more than me told me it sounds like a valve tapping, which he said can get expensive. I had also noticed my truck smoking for a few seconds once I started it up. My friend suggested that I change the oil, maybe that would help. I do change my own oil, and have long been a believer in Lucas Oil Stabilizer, so I was already using that. When I went to buy some oil to change, I saw this stuff and thought I would give it a try. I followed the directions on the bottle. I let my engine cool down, then poured this in and let it run idle for about 5 min. As soon as I started the truck the tapping stopped, I thought it was probably a fluke, no way it works that fast. But I drained the oil changed the filter, added my oil plus the Lucas as usual and no more tapping. Took it for a ride down the interstate, no tapping. Drove to work, about 30 min away, no tapping. Needless to say, I am very happy with how this works and will be using it regularly with all my oil changes.
Everything was perfect thank you
Get specific details about this product from customers who own it.
Ask a question