Dremel 575 4 inch Right Angle Attachment for Rotary Tools

Walmart # 551723817

Dremel 575 4 inch Right Angle Attachment for Rotary Tools

Walmart # 551723817
$19.82$19.82
List $34.99
Free shipping on orders over $35
Free pickup Tue, Jun 26
Sold & shipped byWalmart
1 other seller from $20.11
Compare all 2 sellers
Highlights
Attaches to Dremel rotary tool, makes it easy to work in hard-to-reach spots
Read more....

About This Item

Attaches to Dremel rotary tool, makes it easy to work in hard-to-reach spots
Customer Reviews
2.4 out of 5 Stars
5 stars
3
4 stars
2
3 stars
1
2 stars
4
1 stars
7
1-10 of 17 reviews

Missing Drive Adapter, advertised as quick connect

This is advertised as quick connect, but has a dozen steps — one of which requires an elusive “drive adapter” ... which, if missing, makes the tool worthless.

Broken Shaft

I was in a desperate need to cut through a bolt in a difficult area, so I purchase the EZ lock mandrel and some cutting discs, only to have the shaft of the 575 right angle attachment break within a minute of cutting. So far, I've been unable to find a replacement for this internal shaft component and feel like the right angle attachment and the new EZ lock pieces have been a waste of money.

worked great, won't get into the tighter spots

I bought this to get into a tight spot under my dash for my project truck. Had some rust hidden up under the dash and had to cut it out to replace it with new metal. For the most part this tool helped a lot to cut in a tight area but it is still a little bulky in it's design and was hitting the bottom of the firewall/cowling area with the top of the tool before the cutting disc could make proper contact. I had to replace a barely used disc with a new one every couple minutes 'til the job was done so that i could keep cutting deep enough to get through the sheet metal. Even with that it helped a ton to get the cutting done only leaving the tighter corners and above the steering column to cut by hand. I have to admit to being surprised and somewhat concerned by some of the reviews relating to reliability. I assumed when I bought it that it was two shafts held by bearings and either a universal joint or bevel gears driving the two, but apparently that is not the case.

Nice tool but....

just bought this right angle attachment for my Dremel 4000 and i realized it doesn't come with the "drive coupling" to connect it. So its useless without it. I thought will be included in the package! Where do you buy it ? Can anyone guide me in the right direction, before i trow it in the garbage?

Right Angled Dremel Attachment

Having this right angle attachment makes doing the job(s) so much easier! A definite must if you're a Dremel fan!

Can't hobby without it!

I have owned mine for a few years, honestly seems like it has been forever. I finally bought an additional moto tool No. 4000 and it stays installed on that all the time. I still use my model 285 moto tool I bought in 1992 for general purpose use, replaced the little clear flex drive coupler on it, and the tool keeps going and going. Question on the right angle attachment: Does it ever need lubricating???? If so where, I no longer have the original instruction sheet.

angle attachment

I have the 3000 series dremel and the 575 angle attachment does not work, unless i did something the rotating threaded part of the dremel is to big for the drive shaft of the angle attachment, there for it doesn't spin. Can I have some assistance ? Please thank you.

Shat is weak and easily breaks.

I bought this at True Value for my dremel, used it with cutting disks in hard to reach places to cut/shape steel. The shaft in the bottom of this is made of pressed thin wires to form a square shaft. Well this is weak, and this just twisted apart and broke after only using it a few times. I was disappointed because it was pretty expensive and did not last very long. I do not recommend using it for anything stressful like cutting disks, sanding, or grinding. It seems to be built for light applications only.

Nice tool. Doesn't last.

I bought this right-angle adapter and it worked great for the first few times I used it. Then is self destructed. I bought a different brand adapter (that looked strikingly similar to this one, but was less expensive) and it destructed after the first few uses. Feels like they both stripped the gears inside. Honestly, I wasn't beating on the thing. Kinda feel let down. Not up to Dremel's usual high quality. I won't buy another.

Doesn't work with the 220-01 WorkStation

The part fits well on the tool itself. It appears to be solid and well-made. However, I bought the part to be used with the Dremel 220-01 WorkStation to provide a steady cutting platform with the drill press function. Except that it not compatible with the WorkStation at all. I've kept the part, as I am sure it will be useful. But I am looking at way to utilize the WorkStation in what I need.
Questions & Answers1 question
Get specific details about this product from customers who own it.

Policies & Plans

See any care plans, options and policies that may be associated with this product.
Electrode, Comp-169673245, DC-prod-dal4, ENV-prod-a, PROF-PROD, VER-22.0.9, SHA-55d0d624211aacb48db6e987d15f42ac1ce810eb, CID-