Customers also viewed these products
- $51.06 Was $53.80Save $2.74
- $49.99 Was $60.45Save $10.46
- $24.82 Was $27.85Save $3.03
- $88.87 Was $116.82Save $27.95
- $55.23 Was $59.95Save $4.72
- $58.41 Was $66.46Save $8.05
About this item
About this item
Important Made in USA Origin Disclaimer: For certain items sold by Walmart on Walmart.com, the displayed country of origin information may not be accurate or consistent with manufacturer information. For updated, accurate country of origin data, it is recommended that you rely on product packaging or manufacturer information.
- Rated at 500 watts of maximum power x two channels into two ohms for a total of 1000 watts of maximum power
- Sturdy aluminum casing
- MOSFET circuitry
- Bridgeable design
- Short circuit protection
- Thermal overload protection
- Variable low pass filter
- Variable high pass filter
- Blue LED indicates power status
- Built-in crossover with adjustable frequency
- Adjustable gain with bass boost
|Number of Channels:||2|
|Manufacturer Part Number:||DA1000.2|
|Features:||Overheating Protection , Built-in short circuit|
|Assembled Product Dimensions (L x W x H):||12.00 x 10.00 x 2.00 Inches|
Ask a question
If you would like to share feedback with us about pricing, delivery or other customer service issues, please contact customer service directly.
Questions will be checked against our question guidelines and posted within five to seven business days.
- yes you can bridge it and it has several setting to make a decent sub amp the bridge produces 300 watt rms at 4 ohms. this amp cannot handle a 2 ohm loadby dr3w3310/22/2010Was this answer helpful? (0) (0)Was this answer helpful?
- Yes, it shows to different + and - on edges for bridging it for the 500 watts.by 46and29/4/2010Was this answer helpful? (0) (0)Was this answer helpful?
- ignore what ruffryder is saying about the voice coils. it is bridgable for a single voice coil or SVC subwoofer, but if you have a dual voice coil, or DVC subwoofer, just wire each channel into each coil if you do that, it's basically putting in the same amount of power as it would if it were bridged, its just that the power would be put into each coil and not into a single coilby JakeL6/4/2010Was this answer helpful? (1) (0)Was this answer helpful?
- you can run each channel separately into the sub left channel and right channel into the sub inputs that will give you a 4ohm load into your sub, BUT make sure that your sub is a 4ohm sub not a 2ohm sub or isnt a dual voice coil sub (dvc) if it is it WILL NOT work.by ruffryder4lif5/28/2010Was this answer helpful? (0) (1)Was this answer helpful?
- Oops yaby MrProphet6/19/2010Was this answer helpful? (0) (5)Was this answer helpful?
- you had better make sure when you bridge it it is 4 ohms or higher or you will over heat the amp , it is not 2 ohm stableby 02mustangGT2/10/2011Was this answer helpful? (0) (0)Was this answer helpful?
- Yes 300 watt rms at 4 ohms. This amp cannot handle any 2 ohm loadsby dr3w3310/22/2010Was this answer helpful? (0) (0)Was this answer helpful?
- i have been doing car audio for many a yrs now. this amp specs should be inside the box with the amp the full specs and no it will not deliver 500 watts to each sub. 500 is peak wattage the full wattage the amp is capable of putting into the subs per channel at a short burst. so when your music does a single loud boom for a second it may deliver the full 500 watts. you never however want to run your subs at full peak power it will damage the amp and speakers not right away but what happens is you get clipping or dirty sound so it causes the coils to burn. always run your amp half way or at rms wattage. some amps call it continous wattage it is the power the amp can efeciantly deliver at a continous all day play. rms good peak bad. like them vr subs they sell it plainly states 400 peak but only runs 40 watts niminal it says on the box or again contionous watts you put in 500 rms you may damage the subs. not right away but it will damage them.by plaztiksr4me6/4/2010Was this answer helpful? (1) (0)Was this answer helpful?
- with MOST amps NOT ALL when you bridge them it drops to a 2ohm load, very few stay at a 4ohm load bridged. if your looking for a 4ohm bridged amp try looking for a 8ohm amp thats bridgeable, that would then give you a 4ohm load bridged.by ruffryder4lif7/24/2010Was this answer helpful? (0) (2)Was this answer helpful?
- no, it would notby jeepcherokee3184/18/2010Was this answer helpful? (1) (0)Was this answer helpful?
- The amp will work with a dual V sub if the sub is 8 ohm you have to paralel the sub to get it to 4 ohmsby 02mustangGT2/10/2011Was this answer helpful? (0) (0)Was this answer helpful?
- I'm about 99% sure this will work fine with a dual voice coil sub. All you have to do, is plug it in as if you were plugging in two different speakers. This amp is 2 x 250 so that means it has 2 outputs.by 46and29/4/2010Was this answer helpful? (0) (0)Was this answer helpful?
- There's no reason this amp wont work on a dual voice coil sub. DVC subs are meant for wiring flexibilityby EdwinMD6/26/2010Was this answer helpful? (0) (0)Was this answer helpful?
Check out these related products
- Reduced Price$63.90 List price $96.71Save $32.81
- Clearance$49.95 List price $59.99Save $10.04
- $38.82 Was $46.17Save $7.35
- $38.92 Was $43.40Save $4.48
- Reduced Price$58.74 List price $89.43Save $30.69
- $67.13 Was $73.00Save $5.87