Car Care & Maintenance

Grip 27033 3-Piece Detailing Brush Set

The Grip 27120 is a Long Handle Brush.

Grip 21196 4-Inch Power Suction Cup Dent Puller

Grip 35116 4-piece Long Rotary Carbide Burr Set

Grip 35133 8Pc Double Carbide Rotary Burr Set

Grip 54800 3-Piece Microfiber Auto Cloth Set

Grip 16270 12-Inch Oil Filter Pliers

Features: -Valve lapper tool.

Features: -Head holder.-Use to hold head in vice through spark plug hole.-Use on Big Twin 1948-present.

Features: -Bushing Tool.-Remove and install crankshaft bushing in the support plate on a Twin Cam.-Piloted for accurate operation. Dimensions: -Dimensions: 3.4'' H x 3.4'' W x 6.7'' D.

Features: -Valve Guide Tool.-Use to properly install valve guide seals. Dimensions: -Dimensions: 1'' H x 1'' W x 3.7'' D.

Features: -Twin cam chain tension unload. Dimensions: -Dimensions: 0.4'' H x 2.8'' W x 5.6'' D.

Features: -Use to remove and install the new front 25mm H-D bearing, including ABS or non ABS wheel bearings on most models with 25mm bearings.-Must be used with the earlier JIMS wheel bearing installer and remover tool. Specifications: -25mm whl bearing.

Features: -Installer Driver.-Easily presses the inner cam bearing smoothly into the right case with the cases assembled to the proper depth.-58-Up Big Twin single cam only.-Use to remove bearing. Includes: -Includes aftermarket and S and S motors. Dimensions: -Dimensions: 3'' H x 5'' W x 6'' D.

Features: -Engine Stand.-Material: Heavy-duty steel.-Simplifies the servicing Sporster motors. Dimensions: -Dimensions: 6.30'' H x 9.5'' W x 18'' D.

Features: -Final Drive Locking Tool.-Use to lock the final drive sprocket.-For removing or installing the sprocket nut.-For belt drive sprockets only. Dimensions: -Dimensions: 3.3'' H x 5.3'' W x 5.5'' D.

Features: -Alignment Tool.-Easily aligns the ignition switch housing as the retaining screws are being torqued, giving the ignition switch knob the alignment it needs to help extend the life of the ignition switch housing. Dimensions: -Dimensions: 3.3'' H x 4.3'' W x 9.7'' D.

Features: -Remover.-Removes the fuel tank cam retaining ring safely and without causing damage to the tank.-Use on 2008 XLH fuel tanks. Assembly Instructions: -Used to gain access to the fuel filter or fuel pump assembly and all other parts located inside the gas tank. Dimensions: -Dimensions: 3.3''…

Features: -End Cap.-Made in the USA.-For 55-84 big twin. Assembly Instructions: -Protects sprocket shaft when using crank assembly removing tool or a press.

Features: -Bushing Tool.-Use to remove and replace wrist pin bushings, without removing connecting rod from crankcase. Dimensions: -Dimensions: 1.5'' H x 3'' W x 9'' D.

Features: -Locking Plate.-Use to lock pinion gear, necessary to torque the pinion nut.-Simple to use, align underneath gear and screw into case.-Use Bikers Choice tool to tighten pinion nut.-54-99 Big Twin.-Can also be used on aftermarket and SandS motors. Dimensions: -Dimensions: 1.5'' H x 4'' W x …

Features: -Bearing Simulator.-Made of black Delrin plastic; wont scratch bearing races.-Made in the U.S.A.-For 70-84 Big Twin. Assembly Instructions: -Designed to allow quick and easy removal and replacement of flywheel assembly in the left side crankcase when checking clearances. Dimensions: -Dimen…

Features: -Exhaust Pipe End Shaper Tool.-Use this tool to remove exhaust pipe tip dents.-Use on all models.

Features: -Lock Ring.-Installs spiral lock rings in one easy step without distorting ring, for the safest wrist pin retention possible.-73 and earlier Big Twin and Sportster. Specifications: -Install lock ring in piston having .515 ID wrist pins, like most aftermarket pistons. Dimensions: -Dimension…

Features: -Removal Tool.-Use to safely remove the cam gear from the camshaft on Big Twins.-Precision tool acts as a stable base to keep the camshaft perfectly perpendicular to the press.-To accurately install the cam gear use JIMS No.1290 Cam Gear Alignment Tool (above).-Use on all 1939-99 Big Twin …

Features: -Pivot Bearing Tool For Harley-Davidson.-Fits: 84-11 FXST/FLST.-For removing/installing swingarm pivot bearing H-D no. 9076 or 9270A on 84-11 Softails.-Can also be used to remove/install front fender spherical bearings on 97-02, 04-11 FLSTS/FLSTSB that use H-D bearing no. 9139.-Made in the…

Features: -Shaft Retention Pin.-Locks into the balancers sprocket pin holes to prevent the balancer from turning out of sync with the flywheel. Assembly Instructions: -Secures the engine balancers on Twin Cam 88B engines when servicing the flywheel assembly. Dimensions: -Dimensions: 0.2'' H x 0.2'' …

Features: -Alignment Tool.-Use to check rod straightness without removing rods from case. Dimensions: -Alignment tool is 4.5'' long.-Dimensions: 0.8'' H x 2.8'' W x 7.5'' D.

Features: -Locking Bar.-Use to lock primary for service work. Dimensions: -Dimensions: 0.5'' H x 3'' W x 10'' D.

Features: -Handle Tool.-Fits JIMS valve seal tool.-Use to properly install valve guide seals. Dimensions: -Dimensions: 0.5'' H x 4'' W x 10.80'' D.

Features: -Valve Guide Tool.-Installs shoulderless valve guides to the proper depth, with handle.-Designed for stock style guides with a OD of about .560''.-Installing a shouldered guide, use either.-Use on all Big Twin motors, Twin Cam 88. Includes: -Includes all aftermarket heads. Dimensions: -Dim…